Instrukcja obsługi klucza programującego AKO D14918

D149H181 Ed.08

AKO-D14918

Ten AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

Ostrzeżenia

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

Opis

1. dioda KOM
2. NAGRYWANIE KLUCZ
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. Dioda LED włączona
6. KABEL ZŁĄCZOWY

Zgodność

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

Okablowanie

1. WAŻNY: Pay attention to the orientation of the connector.
2. AKO-80018 
   (Fakultatywny)
3. AKO-D14918

Zasilacz

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

Działanie

WAŻNY: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the KOM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the KOM led starts flashing quickly.
When recording is complete the controller will reset.

Dioda LED włączona

Steady or flashing: Indicates that the key is connected to the controller.

dioda KOM

Stały: Indicates an error in the transmission/reception of data
Szybkie flashowanie: Indicates transmission/reception of data in progress. At the end of the transmission dioda KOM wyłączy się.
Miganie powolne: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

NOTATKA: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

WAŻNY: Nigdy disconnect the programming key during data transmission.

Dane techniczne

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Objętość dostawtage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Specyfikacje środowiskowe:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelony | Hiszpania

35D149181 REV.07 2025

Zastrzegamy sobie prawo do dostarczenia materiałów, które mogą nieznacznie różnić się od opisanych w naszych Kartach Technicznych.
Aktualne informacje są dostępne na naszej stronie webstrona.