Instrukcja instalacji inteligentnego modułu osi Z ATOMSTACK L2

ATOMSTACK-L2-Smart-Z-Axis-Module-featured-image

Logo ATOMSTACK

Inteligentny moduł osi Z ATOMSTACK L2

ATOMSTACK-L2-Smart-Z-Moduł-obraz-produktu

Instrukcja montażu automatycznego regulatora wysokości w osi Z L2-5W/L2-10W/L2-20W/L2-40W

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (1)

Notatka: Obrazy mają wyłącznie charakter poglądowy. Proszę zapoznać się z rzeczywistym produktem. Aby uzyskać więcej informacji, zeskanuj kod QR.

lista

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (2)

Metoda instalacji osi Z

A5 PRO V2/A10 PRO V2

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (3)

Odkręć 4 szt. M4*6 w kierunku przeciwnym do ruchu wskazówek zegara, aby zdjąć suwak

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (4)

Zainstaluj dedykowane złącze A5 Pro V2/A10 Pro V2
Dokręć 4 szt. M4*6

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (5)

A20 PRO V2/A40 PRO V2

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (6)

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra nie ma potrzeby przenoszenia wyłączników krańcowych

Krok 1

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (7)

  1. Odwróć grawer
  2. Wykręcić 2 śruby z tablicy wyłączników krańcowych
  3. Przesuń deskę do przodu, aby wyrównać 2 otworyATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (8)
  4. Zablokuj 2 śruby z powrotem do płyty
  5. Skończyć
  6. Odwróć grawer

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (9)

Laserowa metoda instalacji zunifikowanej

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (10)

Krok: 1 Usuń 4 szt. M3 i suwak laserowy
Krok: 2 Zamontuj suwak laserowy za pomocą 4 śrub M3 wykręconych z kroku 1

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (11)

Uwaga: odkręcić najpierw element mocujący za pomocą śrubokręta krzyżowego z zestawu narzędzi, a następnie zainstaluj suwak laserowy w laserze A48

Metoda połączenia kablowego

Metoda instalacji laserowej
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (12)

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral/ A12 Ultral/A24 Ultral/X12 Ultral/ X24 Ultral

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (13)

A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (14)

Notatka: Po włączeniu zasilania, aby skorzystać z automatycznego regulatora wysokości w osi Z, wystarczy nacisnąć przycisk „automatycznego ustawiania ostrości” na skrzynce sterowniczej, aby automatycznie ustawić ostrość lasera

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (15) ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (16)

A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (17)

Notatka: Wyświetlacz jest potrzebny w przypadku korzystania z automatycznego regulatora wysokości w osi Z. Należy nim sterować od strony wyświetlacza

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (18)

  • Obsługa klienta: Aby zapoznać się ze szczegółową polityką gwarancyjną, odwiedź naszego oficjalnego przedstawiciela webstrona : www.atomstack.com Aby uzyskać wsparcie techniczne i serwis, prosimy o kontakt e-mailowy: wsparcie@atomstack.com
  • Producent: Shenzhen AtomStack Technologies Co., Ltd
  • Adres: 17 piętro, budynek 3A, faza II, inteligentny park, nr 76, Baohe Avenue, kod startowy: tret, dzielnica Longgang, Shenzhen, Guangdong, Chiny
  • Skanowania QR code: LUB czytnik kodów/skaner kodów kreskowych lub dowolna aplikacja ze skanerem

ATOMSTACK-L2-Smart-Z-Moduł-obraz-modułu (19)

Dokumenty / Zasoby

PDF thumbnailInteligentny moduł osi Z L2
Installation Guide · L2, L2 Smart Z-Axis Module, Smart Z-Axis Module, Z-Axis Module, Module

Odniesienia

Published: July 13, 2024
Zaktualizowano: 14 lipca 2024 r.

Pytania i odpowiedzi

Helpful product questions tied to this manual. Each item links to the full Q&A page.

Answered questions

What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?

Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:Cable Verification:...

Read full answer Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?

Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:Z-axis height adjusterLaser sliderA5/P/A10/A20/X20/S20 dedicated connectorM3*6 screwsM4*5 screwsZ-axis connection cableManual2.0/2.5 Allen wrenchCross screwdriverRegarding the...

Read full answer Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?

Based on the installation manual for the ATOMSTACK L2 Smart Z-Axis Module, the components you are looking for are part of the cable connection setup (Section 05):Transfer Board: This is the small PCB (circuit...

Read full answer How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?

To connect the ATOMSTACK L2 Smart Z-Axis Module to your A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly...

Read full answer

Pytania i odpowiedzi

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

  1. I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob

    🇺🇸 Robert asks I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
    Manuals+ clarified question
    Pytanie

    How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?

    Odpowiedź

    Aby połączyć Inteligentny moduł osi Z ATOMSTACK L2 do twojego A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.

    Zgodnie z Section 05 — Cable connection method for the A20 PRO V2:

    • X-Axis Connection: The Z-axis module cable usually connects to the transfer board located on the X-axis carriage.
    • Y-Axis Motor Comparison: While the connector may look similar to a Y-axis motor plug, it is intended for the Z-axis control port. On V2 models, this is often a 4-pin or 6-pin connector located on the breakout board near the laser module mount.
    • Check for the Adapter: Ensure you are using the "Z-axis connection cable" included in the L2 kit (listed as item 4 in the 01-List). One end connects to the L2 module motor, and the other connects to the reserved Z-axis port on the machine's X-axis terminal.

    If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small płytka adaptera lub Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.

    Read the full Q&A page

    Odpowiedź

    1. I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .

      🇺🇸 Robert asks I don't know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don't see any extra ports anywhere .
      Manuals+ clarified question
      Pytanie

      Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?

      Odpowiedź

      Based on the installation manual for the Inteligentny moduł osi Z ATOMSTACK L2, the components you are looking for are part of the cable connection setup (Section 05):

      • Transfer Board: This is the small PCB (circuit board) located on the back or side of the X-axis carriage (the part that moves left and right). On many AtomStack models like the A6, A12, A24, and X24 series, this board is where the main ribbon cable connects.
      • X-axis Terminal: This refers to the specific port on that transfer board. For the L2 module, you typically need to plug the Z-axis connection cable into the port labeled for the Z-axis or the auxiliary port on this board.

      Notatka: If you do not see extra ports, ensure you are looking at the z powrotem of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.

      Read the full Q&A page

      Odpowiedź

      1. I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.

        🇺🇸 Robert asks I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
        Manuals+ clarified question
        Pytanie

        Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?

        Odpowiedź

        Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:

        • Z-axis height adjuster
        • Laser slider
        • A5/P/A10/A20/X20/S20 dedicated connector
        • Śruby M3*6
        • Śruby M4*5
        • Z-axis connection cable
        • Podręcznik
        • Klucz imbusowy 2.0/2.5
        • Śrubokręt krzyżakowy

        Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.

        Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact wsparcie@atomstack.com w celu weryfikacji.

        Read the full Q&A page

        Odpowiedź

        1. Now what do I do ?

          🇺🇸 Robert asks Now what do I do ?
          Manuals+ clarified question
          Pytanie

          What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?

          Odpowiedź

          Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:

          • Weryfikacja kabla: Ensure the Z-axis connection cable is securely plugged into the module and the corresponding port on your laser engraver's motherboard (refer to Section 05 of the manual for your specific model).
          • Konfiguracja oprogramowania: Open your laser control software (LightBurn or LaserGRBL). You may need to enable the Z-axis in the device settings. In LightBurn, go to Ustawienia urządzenia and ensure 'Enable Z-Axis' is toggled on.
          • Skupienie: The L2 module is designed for automatic or simplified focusing. Use the control panel or software commands to move the Z-axis up and down to verify smooth movement before starting a project.
          • Wyłączniki krańcowe: If you are using models like the A6 Pro, A12 Pro, or A24 Pro, the manual notes that you do not need to relocate the limit switches.

          If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.

          >

          Read the full Q&A page

          Odpowiedź

Zadaj pytanie

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.

ATOMSTACK F03-0338-0AA1 Swift Laser Engraver User Manual
14 maja 2026 r.
ATOMSTACK F03-0352-0AA1 Glacier 120W-90W Laser Engraver Installation Guide
13 maja 2026 r.
ATOMSTACK Atelier Laser Engraver Instruction Manual
2 maja 2026 r.
AtomStack F03-0338-0AA1 Swift User Manual
2 maja 2026 r.