1. Wprowadzenie
This manual provides essential instructions for the setup, operation, and maintenance of your RadioMaster Pocket Portable Remote Controller. The RadioMaster Pocket is a compact and lightweight radio transmitter designed for remote control applications, featuring Hall Gimbals and pre-installed EdgeTX firmware. It is available in ExpressLRS or MPM CC2500 versions. Please read this manual thoroughly before using the device to ensure proper functionality and safety.
2. Koniec produktuview i funkcje
The RadioMaster Pocket is engineered for portability and performance. Key features include:
- Kompaktowa konstrukcja: Portable and lightweight with removable stick ends and a foldable antenna for easy transport and storage.
- Hall Effect Gimbals: Equipped with Hall effect gimbals for precise control and smooth centering.
- EdgeTX Firmware: Comes pre-installed with EdgeTX firmware, offering extensive customization and functionality.
- Zintegrowane światła LED: Built-in LED lights provide visual feedback for switch inputs.
- Podświetlany ekran LCD: A backlit LCD screen offers clear visibility of settings and telemetry data.
- Zewnętrzna zatoka modułowa: Compatible with RadioMaster Nano-size modules and TBS Nano Crossfire/Nano Tracer for expanded connectivity options.
- Kompatybilność baterii: Designed for use with 18650 batteries (not included).
Rycina 2.1: Przód view of the RadioMaster Pocket Remote Controller, showcasing its transparent orange casing, gimbals, LCD screen, and control buttons.
Rysunek 2.2: Kątowy view of the RadioMaster Pocket, highlighting the ergonomic design and the foldable antenna in its upright position.
3. Konfiguracja
3.1 Rozpakowanie i zawartość opakowania
Po otwarciu opakowania należy sprawdzić, czy znajdują się w nim wszystkie elementy:
- RadioMaster Pocket Remote Controller
- Torba transportowa
- Kabel USB
- Instrukcje dla użytkownika (ten dokument)
- Sticker Sheet (optional, for customization)
Notatka: 18650 batteries are nie wliczone w cenę i należy je zakupić osobno.
Figure 3.1: Contents of the RadioMaster Pocket package, including the controller, carrying pouch, USB cable, and documentation.
3.2 Instalacja baterii
- Locate the battery compartment cover on the rear of the controller.
- Zdejmij pokrywę.
- Insert two 18650 lithium-ion batteries, ensuring correct polarity (+/-). It is recommended to use flat-top 18650 batteries (65mm length) for optimal fit. Button-top batteries may be too long and cause difficulty in closing the compartment or damage.
- Dokładnie załóż pokrywę komory baterii.
Ważny: Always use high-quality 18650 batteries and ensure they are fully charged before first use.
3.3 Gimbal and Stick End Adjustment
The RadioMaster Pocket features Hall effect gimbals for precise control. The stick ends are removable and can be adjusted or replaced according to user preference.
- To remove stick ends, gently unscrew them counter-clockwise.
- The removed stick ends can be stored in the designated slots on the back of the controller for safekeeping during transport.
- To reattach, screw them clockwise until snug. Do not overtighten.
Rysunek 3.2: Zbliżenie view of a gimbal stick, illustrating the textured, removable stick end.
Rysunek 3.3: Tył view showing the storage slot for a removable stick end, designed for secure transport.
3.4 Rozmieszczenie anten
The controller features a foldable antenna. Before operation, ensure the antenna is unfolded and positioned vertically for optimal signal transmission. Fold it down for compact storage.
3.5 Pierwsze włączenie zasilania
- Press and hold the power button located on the front panel until the LCD screen illuminates.
- The controller will boot into the EdgeTX firmware. Follow any on-screen prompts for initial setup, such as calibration or model selection.
4. Instrukcja obsługi
4.1 EdgeTX Firmware Navigation
The RadioMaster Pocket runs on EdgeTX firmware, providing a powerful and customizable interface.
- Use the navigation buttons (scroll wheel, menu buttons) to move through menus and adjust settings on the backlit LCD screen.
- Refer to the official EdgeTX documentation for detailed instructions on advanced features, model setup, and customization.
4.2 Wiązanie z odbiornikiem
To establish communication with your drone or RC vehicle, the controller must be bound to a compatible receiver. The binding process varies depending on the receiver type (ExpressLRS or CC2500).
- Power on your receiver and place it in binding mode (refer to your receiver's manual for specific instructions).
- On the RadioMaster Pocket, navigate to the Model Setup menu in EdgeTX.
- Select the appropriate internal RF module (ExpressLRS or CC2500) and initiate the binding process.
- Confirm successful binding on both the controller and receiver.
4.3 Podstawowe sterowanie
- Zawieszenie kardanowe: Control primary flight surfaces (throttle, roll, pitch, yaw).
- Przełączniki: Assignable switches (e.g., SA, SB, SC, SD, SE, SF, SG, SH) are used for various functions like arming, flight modes, or special actions. The built-in LED lights provide visual confirmation of switch positions.
- Wykończenia: Digital trims allow fine-tuning of control surfaces.
- Zewnętrzna zatoka modułowa: For use with compatible external modules to extend functionality or range.
Rysunek 4.1: Góra view of the RadioMaster Pocket, illustrating the various switches and the foldable antenna mechanism.
5. Konserwacja
- Czyszczenie: Do czyszczenia zewnętrznej części kontrolera używaj miękkiej, suchej ściereczki. Unikaj środków czyszczących o właściwościach ściernych i rozpuszczalników.
- Składowanie: Store the controller in its carrying pouch in a cool, dry place away from direct sunlight and extreme temperatures. Ensure the antenna is folded and stick ends are removed and stored if desired.
- Aktualizacje oprogramowania układowego: Regularly check the official RadioMaster or EdgeTX websites for firmware updates to ensure optimal performance and access to new features. Use the provided USB cable for updates.
- Pielęgnacja baterii: Remove batteries if the controller will not be used for an extended period. Store batteries in a safe, cool place.
6. Rozwiązywanie Problemów
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Kontroler nie włącza się. |
|
|
| Unable to bind to receiver. |
|
|
| Gimbals feel stiff or unresponsive. |
|
|
7. Specyfikacje
- Wymiary produktu: 6.57 x 6.1 x 2.87 cala
- Waga przedmiotu: 1.15 funta
- Numer modelu: Kieszeń
- Producent: RadioMaster
- Marka (Sprzedawca): RotorLogika
- Dodatek specjalny: ELRS (ExpressLRS version) or MPM CC2500 (Multi-protocol version)
- Maksymalna liczba obsługiwanych urządzeń: 1 (per binding)
- Zgodne urządzenia: Dron FPV
- Technologia łączności: Częstotliwość radiowa
- Oprogramowanie sprzętowe: EdgeTX (pre-installed)
- Zawieszenie kardanowe: Efekt Halla
- Typ baterii: 2 x 18650 (not included, flat-top recommended)
8. Gwarancja i wsparcie
For warranty information, technical support, or service inquiries, please contact the retailer where you purchased your RadioMaster Pocket Remote Controller or visit the official RadioMaster webZachowaj dowód zakupu na wypadek roszczeń gwarancyjnych.
Producent: RadioMaster
Seller/Distributor: RotorLogika
