Instrukcja obsługi paska LED RGB COB BTF-LIGHTING FCOB WS2811 IC

1. Koniec produktuview

The BTF-LIGHTING FCOB WS2811 IC RGB COB LED Strip is a flexible, high-density lighting solution designed for various DIY lighting projects. It features addressable WS2811 IC chips, allowing for vibrant color chasing and uniform light distribution. This strip operates on DC24V and is 16.4 feet long with 864 LEDs per meter and 24 ICs per meter, with a 12mm width. It is rated IP30 for indoor use.

Figure 1: Product packaging showing the LED strip, connectors, and clips.

Główne cechy:

• Addressable COB RGB LED Strip: DC24V, 16.4FT, 864LED/m, 24IC/m. One WS2811 IC Chip drives 36 LEDs.
• Stunning Lighting Effects: Over 16 million vibrant hues with diverse dynamic lighting effects like rainbow, wave, and snake patterns.
• Ultra Bright and Uniform: Flip Chip On Board (FCOB) technology ensures bright, soft, and uniform light without dark areas.
• Cuttable and Re-attachable: Flexible strip with cut marks every 1.64 inches (41.6mm). Features 3PIN connectors for series connection.
• Trwała konstrukcja: Adopts a double-layer copper PCB board for better electronic conductivity and heat dissipation, ensuring a lifespan of over 65,000 hours.

2. Zawartość opakowania

Przed otwarciem paczki należy sprawdzić, czy wszystkie przedmioty znajdują się w opakowaniu i są w dobrym stanie.

• 1 x FCOB WS2811 IC RGB COB LED Strip (DC24V, 16.4FT, 864LED/m)
• 1 x 3PIN Male Connector
• 3 x Fixed Clips

Note: Power supply and controller are NOT included and must be purchased separately.

3. Konfiguracja i instalacja

Follow these steps for proper installation of your LED strip. Ensure the installation surface is thoroughly cleaned and dried before applying the strip.

1. Przygotuj powierzchnię: Clean the desired installation area to ensure it is free of dust, grease, and moisture. This will ensure optimal adhesion of the strip's self-adhesive backing.
2. Zmierz i tnij (opcjonalnie): If a shorter length is required, the FCOB LED strip can be cut at designated cut marks, which are spaced every 1.64 inches (41.6mm). Use sharp scissors to ensure a clean cut.
3. Złącza: The strip comes with 3PIN connectors on both ends (one female, one male). These allow for end-to-end series connection. Additional connectors (sold separately) can be used for custom configurations or to re-attach cut sections.
4. Zastosuj pasek: Peel off the protective backing from the self-adhesive tape on the back of the LED strip. Carefully press the strip onto the prepared surface, ensuring firm contact along its entire length.
5. Zabezpiecz za pomocą klipsów: Use the provided fixed clips for additional security, especially on uneven surfaces or in areas where the strip might be subject to movement.
6. Connect to Controller and Power Supply: Connect the 3PIN male connector of the LED strip to a compatible WS2811 IC controller (sold separately). Then, connect the controller to a suitable DC24V power supply (sold separately). Ensure the voltage of the power supply matches the strip's requirement.

Figure 2: Illustration of the LED strip's cuttable points and data direction.

Figure 3: Connection diagrams for the LED strip, illustrating how to connect multiple segments. Note that connectors are sold separately.

Figure 4: Proper application of the LED strip using its self-adhesive backing and securing clips.

4. Instrukcja obsługi

The FCOB WS2811 IC RGB LED Strip requires an external controller for operation. This strip is compatible with a variety of programmable and app-controlled devices.

4.1 Compatible Controllers:

The LED strip is compatible with the following types of controllers (sold separately):

• Programmable Controllers: Such as K1000C.
• APP Controllers: Including SP630E, SP611E, SP105E, SP602E, SP608E.
• Music Controllers: Such as CSY08, SP107E.
• Smart WiFi Voice Controllers: Na przykładample, SP530E.
• DIY Controllers: Compatible with Arduino and Raspberry Pi for custom programming.

Rysunek 5: Examples of compatible controllers for the LED strip (controllers sold separately).

Rysunek 6: Example of a smartphone application interface for controlling the LED strip, demonstrating various color and effect options.

4.2 Dynamic Lighting Effects:

With the appropriate controller, you can achieve a wide range of dynamic lighting effects and adjust static colors. The high IC density (24 ICs/m) allows for more complex and vibrant color patterns compared to strips with lower IC density.

Figure 7: Visual comparison demonstrating the uniform light output of the FCOB WS2811 IC LED strip compared to a standard WS2811 IC strip with visible dark areas.

5. Konserwacja

To ensure the longevity and optimal performance of your LED strip, follow these simple maintenance guidelines:

• Czyszczenie: Periodically clean the surface of the LED strip with a soft, dry cloth to remove dust and debris. Avoid using harsh chemicals or abrasive materials.
• Kontrola połączenia: Regularly inspect all connections (strip to connector, connector to controller, controller to power supply) to ensure they are secure and free from corrosion.
• Warunki środowiskowe: This LED strip has an IP30 rating, meaning it is designed for indoor use and is not protected against water or moisture. Avoid exposing the strip to liquids or high humidity.
• Zarządzanie ciepłem: While the double-layer copper PCB aids in heat dissipation, ensure the strip is installed in a well-ventilated area, especially when operating at full brightness, to prevent overheating.

6. Rozwiązywanie Problemów

If you encounter any issues with your BTF-LIGHTING FCOB WS2811 IC RGB COB LED Strip, please refer to the following common troubleshooting tips:

• Strip Not Lighting Up:
  • Check if the power supply is correctly connected and providing the correct DC24V output.
  • Ensure all connectors are securely attached and the polarity is correct.
  • Verify that the controller is powered on and functioning correctly.
  • Inspect the strip for any visible damage or cuts outside the designated cut marks.
• Nieprawidłowe kolory lub migotanie:
  • Confirm that the controller settings match the WS2811 IC type.
  • Check for loose connections between the strip and the controller.
  • Ensure the power supply is adequate for the length of the strip being used.
• Nierównomierne rozświetlenie lub ciemne plamy:
  • While FCOB technology minimizes dark spots, ensure the strip is not bent too sharply, which could damage internal components.
  • Verify that the power supply is sufficient and voltage drop is not occurring over long runs.

For further assistance, troubleshooting, or replacement inquiries, please contact BTF-LIGHTING customer service.

7. Specyfikacje

8. Gwarancja i wsparcie

BTF-LIGHTING provides a 12-miesięczna bezproblemowa gwarancja for this product. Our customer service team is available 24/7 to assist you with any questions regarding purchase, installation, troubleshooting, or replacements.

Aby uzyskać pomoc, odwiedź stronę Sklep BTF-LIGHTING na Amazon or contact our customer service directly.