INFICON D-TEK Stratus Refrigerant Leak Detector and Portable Monitor User Manual

1. Wprowadzenie

The INFICON D-TEK Stratus is an advanced refrigerant leak detector and portable monitor designed for efficient and accurate leak detection. This device combines the precision of D-TEK Select detectors with the broad area scanning capability of a portable monitor, offering a comprehensive solution for identifying refrigerant leaks.

It features an infrared sensor, dual operating modes (Cloud Hunting and Pinpoint), and a robust design for field use. This manual provides essential information for the proper setup, operation, and maintenance of your D-TEK Stratus unit.

2. Główne cechy

• Dwa tryby pracy: Cloud Hunting mode for locating the general area of highest concentration and Pinpoint mode for precise leak identification.
• Advanced Infrared Sensor: Redesigned for enhanced performance and an extended lifespan of over 2,000 hours.
• Wysoka czułość: Detects leaks as small as 0.03 oz./year (1 g/year) without degradation over time.
• Versatile Refrigerant Detection: Compatible with CFCs, HCFCs, HFCs, HFOs, and A2Ls. Optional sensors are available for CO2 and flammable refrigerants.
• Field Replaceable Components: Sensor, battery, filters, and probe are easily replaceable in the field.
• Bateria litowo-jonowa: Provides extended operation with quick charge capability.
• Przyjazny dla użytkownika interfejs: Large, easy-to-read LCD display and intuitive controls.
• Automatic and Manual Zero Modes: For optimal calibration in various environments.

3. Zawartość opakowania

Po otwarciu opakowania należy sprawdzić, czy znajdują się w nim wszystkie poniższe elementy:

Image: The INFICON D-TEK Stratus device shown with its complete set of accessories, including the main unit, various international AC wall chargers, a DC car charger, earbuds, spare filters, an extra-long probe, an infrared sensor, a lithium-ion battery, and a durable carry case.

• D-TEK Stratus Unit
• Infrared Sensor (pre-installed or separate)
• Akumulator litowo-jonowy (wstępnie zainstalowany lub osobno)
• AC Wall Charger (US & International adapters)
• Ładowarka samochodowa prądu stałego
• Extra-Long Probe
• Słuchawki douszne
• Filtry zapasowe
• Etui transportowe

4. Konfiguracja

4.1 Pierwsze ładowanie

Before first use, fully charge the lithium-ion battery. Connect the provided AC wall charger or DC car charger to the micro USB power input port on the device. The charging indicator on the display will show the charging status.

4.2 Sensor and Filter Installation

Ensure the infrared sensor and filter are correctly installed. The sensor is typically pre-installed. Filters are located at the probe tip and should be clean and free of debris for optimal performance.

Image: The INFICON D-TEK Stratus device, showing its main body, flexible probe, and digital display indicating a refrigerant concentration of 1345 ppm. This image highlights the device's ergonomic design and clear interface.

4.3 Urządzenie ponadview

Zapoznaj się z elementami sterującymi i komponentami urządzenia:

Obraz: szczegółowy view of the INFICON D-TEK Stratus, with labels pointing to key components such as the probe tip/filter, headphone jack, volume button, battery cover, eject button, micro USB power input, SENS/ZERO button, and Mode/Max button. The power button is indicated as not visible in this view.

• Przycisk zasilania: Włącza/wyłącza urządzenie.
• Mode/Max Button: Toggles between Cloud Hunting and Pinpoint modes, and displays maximum readings.
• SENS/ZERO Button: Adjusts sensitivity and performs manual zeroing.
• Gniazdo słuchawkowe: For connecting earbuds for audio alerts.
• Przycisk głośności: Adjusts audio alert volume.
• Wejście zasilania Micro USB: Do ładowania urządzenia.
• Przycisk wysuwania: Releases the sensor module for replacement.
• Pokrywa baterii: Umożliwia dostęp do komory baterii.
• Probe Tip/Filter: The detection point, containing a replaceable filter.

5. Instrukcja obsługi

5.1 Włączanie i początkowa kalibracja

1. Naciśnij i przytrzymaj przycisk zasilania, aby włączyć urządzenie.
2. Allow the device to warm up and perform its automatic zeroing process in a clean, leak-free environment. This ensures accurate readings.

5.2 tryby pracy

The D-TEK Stratus offers two distinct operating modes for efficient leak detection:

Image: This graphic illustrates the two primary operating modes of the INFICON D-TEK Stratus. The top section shows "Cloud Hunting Mode" with a digital display indicating 1345 ppm, used for finding areas of highest concentration. The bottom section shows "Pinpoint Mode" with a color-coded bar graph, used for precisely locating the leak source.

5.2.1 Cloud Hunting Mode

• Use this mode to quickly scan large areas and identify the general vicinity of a refrigerant leak.
• The display will show refrigerant concentration in parts per million (ppm).
• Move the probe slowly through the suspected area. Higher readings indicate proximity to a leak.

5.2.2 Tryb precyzyjnego namierzania

• Once the general leak area is identified using Cloud Hunting, switch to Pinpoint mode for precise leak location.
• In this mode, the device provides a more focused indication, often with a visual bar graph or escalating audio tone, to guide you directly to the leak source.
• Move the probe very slowly and methodically around suspected leak points.

5.3 Adjusting Sensitivity and Zeroing

• Wrażliwość: Press the SENS/ZERO button to cycle through sensitivity levels. Adjust sensitivity based on the size of the suspected leak and environmental conditions.
• Manual Zero: If the device is alarming in a clean environment, move the probe to an area free of refrigerants and press and hold the SENS/ZERO button to perform a manual zero.

6. Informacje o czujniku

The D-TEK Stratus utilizes an advanced infrared sensor for detecting a wide range of refrigerants. The sensor has an expected lifespan of over 2,000 hours.

6.1 Compatible Refrigerants

The standard infrared sensor detects:

• CFCs (Chlorofluorocarbons)
• HCFCs (Hydrochlorofluorocarbons)
• HFCs (Hydrofluorocarbons)
• HFOs (Hydrofluoroolefins)
• A2Ls (Mildly Flammable Refrigerants)

6.2 Opcjonalnych Czujników

For detecting other gases, optional sensors are available and can be easily interchanged:

Image: This image displays three different sensor modules for the INFICON D-TEK Stratus. The red sensor is for CFCs, HCFCs, HFCs, HFOs, and A2Ls (included refrigerant sensor). The silver sensor is for flammable refrigerants (requires optional sensor). The green sensor is for CO2 (requires optional sensor). This illustrates the device's versatility with interchangeable sensors.

• Czujnik CO2: Required for detecting Carbon Dioxide.
• Flammable Refrigerants Sensor: Required for detecting flammable refrigerants.

7. Informacje o baterii

The D-TEK Stratus is powered by a rechargeable Lithium-Ion battery, providing approximately 9 hours of continuous operation on a full charge. The battery is designed for quick charging.

7.1 Ładowanie

Use only the INFICON-supplied AC wall charger or DC car charger. Connect the charger to the micro USB port on the device. The battery indicator on the display will show the charging status.

7.2 Wymiana baterii

The Lithium-Ion battery is field replaceable. Refer to the maintenance section for instructions on how to safely replace the battery.

8. Konserwacja

Regular maintenance ensures the longevity and accuracy of your D-TEK Stratus.

8.1 Wymiana filtra

The probe tip contains a filter that prevents contaminants from entering the sensor. Replace the filter regularly, especially if operating in dusty or dirty environments, or if you notice a decrease in sensitivity. Spare filters are included with your unit.

1. Gently unscrew the probe tip.
2. Wyjmij stary filtr.
3. Włóż nowy filtr.
4. Screw the probe tip back on securely.

8.2 Wymiana czujnika

The infrared sensor is field replaceable. When the sensor reaches the end of its lifespan (indicated by a message on the display or persistent inaccurate readings), it should be replaced.

1. Sprawdź, czy urządzenie jest wyłączone.
2. Locate the eject button (refer to Device Overview).
3. Press the eject button to release the sensor module.
4. Carefully remove the old sensor.
5. Insert the new sensor module, ensuring it clicks into place.
6. Power on the device and allow it to calibrate with the new sensor.

8.3 Czyszczenie

Przetrzyj zewnętrzną powierzchnię urządzenia reklamąamp cloth. Do not use abrasive cleaners or solvents. Ensure the probe tip and sensor area remain clean and free of obstructions.

9. Rozwiązywanie Problemów

If you encounter issues with your D-TEK Stratus, consider the following common solutions:

• Urządzenie nie włącza się:
  • Upewnij się, że bateria jest w pełni naładowana.
  • Sprawdź, czy bateria jest prawidłowo zainstalowana.
• Inaccurate Readings or Constant Alarm:
  • Perform a manual zero in a clean air environment.
  • Check and replace the probe tip filter if it is dirty or clogged.
  • Verify the sensor is correctly installed and not at the end of its lifespan.
  • Ensure the correct sensor type is installed for the refrigerant being detected.
• Brak wykrycia:
  • Increase the sensitivity setting.
  • Ensure the probe is moved slowly and methodically.
  • Check the sensor for proper installation and remaining lifespan.
  • Confirm the presence of refrigerant; test with a known leak source if possible.
• Krótki czas pracy baterii:
  • Przed użyciem upewnij się, że akumulator jest w pełni naładowany.
  • Consider replacing the battery if it no longer holds a charge effectively.

For persistent issues, contact INFICON customer support.

10. Specyfikacje

11. Gwarancja i wsparcie

INFICON stands behind the quality of its products.

Image: This graphic highlights INFICON's commitment to quality and customer support. It features icons and text indicating a "2 Year Replacement Warranty," "Made in the USA with US and Imported Parts," and "US Technician Support" available via email and phone.

11.1 Informacje o gwarancji

The INFICON D-TEK Stratus comes with a Two-Year Replacement WarrantyNiniejsza gwarancja obejmuje wady materiałowe i wykonawcze powstałe w wyniku normalnego użytkowania. Prosimy zachować dowód zakupu na potrzeby roszczeń gwarancyjnych.

11.2 Wsparcie techniczne

For technical assistance, troubleshooting, or warranty inquiries, please contact INFICON US Technician Support. Support is available via email and phone.

The product is proudly Wyprodukowano w USA with a combination of US and imported parts, reflecting a commitment to quality manufacturing.