1. Koniec produktuview
The Dorman 46912 Hood Release Handle Assembly is a direct replacement component designed to restore the functionality of your vehicle's hood release mechanism. This assembly is engineered to fit and perform like the original equipment, ensuring reliable operation. It is constructed from high-quality materials for durability and longevity.
Rysunek 1.1: Przód view of the Dorman 46912 Hood Release Handle Assembly, showing the hood icon.
2. Zawartość opakowania
Przed rozpoczęciem instalacji sprawdź, czy wszystkie komponenty są obecne:
- 1 x Dorman 46912 Hood Release Handle Assembly
3. Informacje dotyczące bezpieczeństwa
Always observe general automotive safety precautions when working on your vehicle. Failure to do so may result in injury or damage to the vehicle.
- Upewnij się, że pojazd jest zaparkowany na równej powierzchni i ma zaciągnięty hamulec postojowy.
- Wyłącz silnik i wyjmij kluczyk ze stacyjki.
- Należy nosić odpowiedni sprzęt ochrony osobistej, taki jak rękawice i okulary ochronne.
- Jeśli masz wątpliwości co do któregokolwiek etapu instalacji, skonsultuj się z wykwalifikowanym technikiem samochodowym.
4. Instrukcje instalacji
This hood release handle assembly is designed for direct replacement and features an easy-to-install clip-on mechanism. Specific installation steps may vary slightly depending on your vehicle's make and model. Refer to your vehicle's service manual for detailed instructions if necessary.
Ogólne kroki instalacji:
- Locate the Existing Handle: Identify the current hood release handle, typically located on the driver's side, beneath the dashboard.
- Odłącz kabel: Carefully detach the hood release cable from the existing handle. This may involve releasing a clip or a small retaining pin.
- Usuń starą klamkę: Unclip or unfasten the old hood release handle from its mounting point.
- Attach the New Handle: Connect the hood release cable to the Dorman 46912 assembly. Ensure the cable is securely seated.
- Mount the New Handle: Clip the new Dorman 46912 Hood Release Handle Assembly into its designated mounting location. Ensure it is firmly secured.
- Funkcjonalność testu: Gently pull the new handle to ensure it operates smoothly and releases the hood latch correctly. Close the hood and re-test to confirm proper engagement and release.
Rysunek 4.1: Strona view of the Dorman 46912 Hood Release Handle Assembly, illustrating the internal cable connection point.
Rysunek 4.2: Tył view of the Dorman 46912 Hood Release Handle Assembly, highlighting the clip-on attachment mechanism.
5. Instrukcja obsługi
To open your vehicle's hood using the Dorman 46912 Hood Release Handle Assembly:
- Ensure the vehicle is stationary and the engine is off.
- Locate the hood release handle, typically on the lower left side of the driver's dashboard.
- Pull the handle firmly and steadily towards you. You should hear a click as the primary hood latch disengages.
- Proceed to the front of the vehicle. The hood will be slightly ajar.
- Locate the secondary safety latch, usually positioned under the front edge of the hood, near the center. Push or lift this latch to fully release the hood.
- Podnieś maskę i zabezpiecz ją za pomocą pręta podporowego, jeśli jest to wymagane.
To close the hood, lower it gently until it rests on the secondary latch, then press down firmly on the center of the hood until the primary latch engages with a click. Ensure the hood is fully closed and secured before driving.
6. Konserwacja
The Dorman 46912 Hood Release Handle Assembly is designed for long-lasting performance with minimal maintenance. However, periodic inspection can help ensure continued reliable operation:
- Kontrola wizualna: Periodically check the handle for any signs of wear, cracks, or damage.
- Cable Lubrication: If the hood release mechanism feels stiff, consider lubricating the hood release cable and latches with a suitable automotive lubricant. Consult your vehicle's service manual for recommended lubrication points and types.
- Czystość: Keep the area around the handle free from dirt and debris that could impede its movement.
7. Rozwiązywanie Problemów
If you encounter issues with your Dorman 46912 Hood Release Handle Assembly, consider the following:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Handle feels loose or detached. | Handle not properly clipped into mounting point. | Re-secure the handle firmly into its mounting location. |
| Handle pulls but hood does not release. | Cable disconnected from handle or latch; cable stretched or broken; hood latch mechanism seized. | Inspect cable connection at both the handle and the hood latch. Check cable for damage. Lubricate hood latch mechanism. If cable is damaged, it may need replacement. |
| Handle is stiff or difficult to pull. | Lack of lubrication in cable or latch mechanism; debris obstructing movement. | Lubricate the hood release cable and hood latch mechanism. Clean any debris from the handle's pivot points. |
Jeśli podjęcie prób rozwiązania problemu nie przyniesie rezultatu, zaleca się konsultację z profesjonalnym mechanikiem samochodowym.
8. Specyfikacje produktu
| Marka | Uśpiony |
| Numer modelu | 46912 |
| Kolor | Czarny |
| Wykończenie zewnętrzne | Obrobiony maszynowo |
| Funkcja specjalna | Łatwy w instalacji |
| Zawarte komponenty | Dorman 46912: Hood Release Handle Assembly |
| Typ zamka | Brak blokady |
| Waga przedmiotu | 1.44 uncji |
| Wymiary produktu | 1.91 x 3.45 x 5.49 cala |
| Mechanizm mocowania uchwytu | Przypnij |
| UPC | 194883234604 |
| Numer(y) części OEM | 4589482AB, 4589482AC, 5109273AA, 5160352AB, 5160352AC |
9. Gwarancja i wsparcie
Dorman products are backed by a team of product experts in the United States and more than a century of automotive experience, ensuring trustworthy quality. For specific warranty information or technical support, please refer to the official Dorman webodwiedź witrynę lub skontaktuj się bezpośrednio z obsługą klienta Dorman.
Więcej informacji znajdziesz w sklepie Dorman Store: Oficjalny sklep Dorman
