AeroCool Mirage L240 ARGB Liquid Cooler User Manual

Wstęp

The AeroCool Mirage L240 ARGB Liquid Cooler is a high-performance all-in-one (AIO) liquid cooling solution designed for efficient heat dissipation from your CPU. Featuring a 240mm radiator, two 120mm Addressable RGB (ARGB) fans, and a unique infinity mirror pump design, it provides both superior cooling capabilities and stunning visual effects for your PC build. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your cooler.

Figure 1: AeroCool Mirage L240 ARGB Liquid Cooler with its vibrant ARGB fans and pump.

Co jest w pudełku

Przed rozpoczęciem instalacji należy sprawdzić, czy wszystkie elementy są obecne.

• AeroCool Mirage L240 ARGB Liquid Cooler (Radiator, Pump, and Tubing pre-assembled)
• 2 x 120mm wentylatory ARGB
• Mounting Hardware Kit (for Intel and AMD sockets)
• Śruby montażowe wentylatora i chłodnicy
• Pasta termoprzewodząca (gotowa do użycia lub w tubce)
• ARGB Controller (if not motherboard sync compatible)
• Instrukcja obsługi (ten dokument)

Note: The provided product information only listed "Camera body" for "whats_in_the_box". This is a generic list for a liquid cooler.

Specyfikacje

Konfiguracja i instalacja

Follow these steps carefully to install your AeroCool Mirage L240 ARGB Liquid Cooler.

1. Przygotuj swój system

• Wyłącz komputer i odłącz go od gniazdka ściennego.
• Open your PC case and remove any existing CPU cooler.
• Dokładnie wyczyść powierzchnię procesora alkoholem izopropylowym, aby usunąć starą pastę termoprzewodzącą.

2. Montaż chłodnicy i wentylatorów

1. Attach the two 120mm ARGB fans to the radiator using the long fan screws provided. Ensure the fan airflow direction is as desired (typically exhaust out of the case or intake into the case).
2. Mount the radiator assembly to an available 240mm fan mount location in your PC case (e.g., top, front, or rear). Use the shorter radiator screws to secure it.

Figure 2: Radiator and fans assembled, ready for mounting in the PC case.

3. Install CPU Pump/Cold Plate

1. Select the appropriate mounting brackets for your CPU socket (Intel or AMD) from the hardware kit. Attach them to the pump unit.
2. If thermal paste is not pre-applied, apply a small pea-sized amount to the center of your CPU's integrated heat spreader (IHS).
3. Carefully place the pump/cold plate assembly onto the CPU, aligning the mounting holes.
4. Secure the pump to the motherboard using the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.

Figure 3: The copper cold plate of the pump unit, which makes contact with the CPU.

4. Podłącz kable

• Connect the pump's 3-pin power cable to the "CPU_FAN" or "AIO_PUMP" header on your motherboard.
• Connect each fan's 4-pin PWM cable to available fan headers on your motherboard (e.g., "SYS_FAN").
• Connect the ARGB cables from the fans and pump to your motherboard's 3-pin 5V ARGB header or to the included ARGB controller. Ensure correct polarity to avoid damage.
• Organize cables for good airflow and aesthetics.

Instrukcja obsługi

Once installed, the AeroCool Mirage L240 ARGB Liquid Cooler operates automatically based on your motherboard's fan control settings. The pump runs continuously to circulate coolant, and fan speeds adjust according to CPU temperature.

Sterowanie oświetleniem ARGB

• Synchronizacja płyty głównej: If connected to a compatible motherboard ARGB header, you can control the lighting effects using your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync).
• ARGB Controller: If using the included ARGB controller (if applicable), refer to its specific instructions for changing lighting modes, colors, and brightness.

Konserwacja

Regularna konserwacja pomaga zapewnić długowieczność i optymalną wydajność chłodnicy cieczy.

• Czyszczenie kurzu: Periodically (every 3-6 months, or more often in dusty environments) power off your PC and use compressed air to clean dust from the radiator fins and fan blades. This prevents airflow restriction and maintains cooling efficiency.
• Kontrola wizualna: Check the tubing and connections for any signs of leaks or damage. While rare, early detection can prevent issues.
• Działanie wentylatora: Ensure all fans are spinning freely and quietly. Replace any fans that become noisy or stop working.

Figure 4: Regularly clean dust from the radiator and fan blades for optimal performance.

Rozwiązywanie problemów

If you encounter issues with your AeroCool Mirage L240 ARGB Liquid Cooler, refer to the following common problems and solutions.

Gwarancja i wsparcie

AeroCool products are designed for reliability and performance. For warranty information, technical support, or to inquire about replacement parts, please visit the official AeroCool webstronie lub skontaktuj się z działem obsługi klienta.

Urzędnik Webstrona: www.aerocool.io

Please have your product model number (MIRAGEL240W or ACLA-MR2412771) and purchase date ready when contacting support.