Instrukcja obsługi układu chłodzenia cieczą AZZA LCAZ-240C-ARGB

Wstęp

Thank you for choosing the AZZA LCAZ-240C-ARGB Liquid Cooling System. This manual provides essential information for the proper installation, operation, and maintenance of your new CPU cooler. Please read this manual thoroughly before installation to ensure optimal performance and longevity of your system.

Rysunek 1: The AZZA LCAZ-240C-ARGB Liquid Cooling System, featuring a 240mm radiator, two 12cm ARGB fans, and an ARGB pump/cold plate assembly. The fans and pump display vibrant, customizable lighting.

Zawartość opakowania

Verify that all components are present before beginning installation. If any items are missing or damaged, please contact AZZA support.

• AZZA LCAZ-240C-ARGB Radiator with Pump/Cold Plate Assembly
• Two 120mm ARGB Fans
• Mounting Hardware Kit (for Intel and AMD sockets)
• Fan and ARGB Splitter Cables
• Pasta termoprzewodząca (gotowa do użycia lub w tubce)
• Instrukcja obsługi (ten dokument)

Specyfikacje

Konfiguracja i instalacja

Before proceeding, ensure your computer is powered off and unplugged from the wall outlet. Refer to your motherboard and PC case manuals for specific mounting locations and clearances.

1. Przygotuj płytę główną: Install the appropriate backplate and standoffs for your CPU socket (Intel or AMD) onto the motherboard.
2. Nałóż pastę termoprzewodzącą: If thermal paste is not pre-applied to the cold plate, apply a small, pea-sized amount to the center of your CPU's integrated heat spreader (IHS).
3. Mount Cold Plate: Carefully place the pump/cold plate assembly onto the CPU, aligning the mounting holes. Secure it with the provided thumb screws or nuts, tightening them in a diagonal pattern until snug. Do not overtighten.
4. Montaż chłodnicy i wentylatorów: Attach the two 120mm fans to the radiator using the long screws. Ensure the fan airflow direction is appropriate for your case (intake or exhaust). Mount the radiator assembly to an available fan mount in your PC case (e.g., top, front, or rear).
5. Podłącz kable:
   • Connect the pump's 3-pin power cable to a dedicated AIO_PUMP or CPU_FAN header on your motherboard.
   • Connect the two fan 4-pin PWM cables to the included fan splitter cable, then connect the splitter to a CPU_FAN or SYS_FAN header on your motherboard.
   • Connect the ARGB cables from the fans and pump to the included ARGB splitter cable, then connect the splitter to a 5V 3-pin ARGB header on your motherboard. Do not connect to a 12V RGB header.
6. Zarządzanie kablami: Route all cables neatly to avoid interference with other components and to improve airflow.

Instrukcja obsługi

Once installed, the AZZA LCAZ-240C-ARGB operates automatically.

• Włączanie: After completing installation and securing all connections, power on your computer.
• Ustawienia BIOS/UEFI: Access your motherboard's BIOS/UEFI to ensure the CPU_FAN or AIO_PUMP header is set to PWM mode (if applicable) and that fan curves are configured for optimal cooling and noise levels.
• Sterowanie ARGB: Use your motherboard's ARGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize the lighting effects of the fans and pump.
• Monitoruj temperatury: Use monitoring software to observe CPU temperatures, especially during initial use and under load, to confirm proper cooling performance.

Konserwacja

Regular maintenance helps ensure the longevity and efficiency of your liquid cooling system.

• Usuwanie kurzu: Periodically clean dust from the radiator fins and fan blades using compressed air or a soft brush. Dust accumulation can impede airflow and reduce cooling performance.
• Kontrola rur: Occasionally check the tubing for any signs of kinks, leaks, or damage.
• Działanie wentylatora: Ensure both fans are spinning freely and quietly. Replace any fans that become excessively noisy or stop functioning.
• Działanie pompy: Listen for any unusual noises from the pump. A constant, low hum is normal, but grinding or rattling sounds may indicate an issue.

Rozwiązywanie problemów

If you encounter issues with your AZZA LCAZ-240C-ARGB, refer to the following common problems and solutions.

• Wysokie temperatury procesora:
  • Ensure the pump is running and connected to a constant power source (AIO_PUMP header).
  • Verify that the cold plate is making proper contact with the CPU and that thermal paste was applied correctly.
  • Check that fans are spinning and oriented correctly for optimal airflow through the radiator.
  • Wyczyść kurz nagromadzony na żebrach chłodnicy.
• Fans Not Spinning or ARGB Not Lighting Up:
  • Confirm all fan and ARGB cables are securely connected to the motherboard headers and splitters.
  • Ensure the ARGB cable is connected to a 5V 3-pin ARGB header, not a 12V 4-pin RGB header.
  • Check your motherboard's BIOS/UEFI settings for fan control and ARGB settings.
  • Sprawdź, czy oprogramowanie ARGB Twojej płyty głównej jest zainstalowane i prawidłowo skonfigurowane.
• Nietypowy hałas pompy:
  • Ensure the pump is receiving adequate power.
  • Sprawdź, czy w pętli nie ma pęcherzyków powietrza, delikatnie przechylając obudowę komputera.
  • If the noise persists and is disruptive, contact AZZA support.

Gwarancja i wsparcie

AZZA products are designed for reliability and performance. This product comes with a limited warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official AZZA webstrona.

For technical support, troubleshooting assistance, or to inquire about replacement parts, please contact AZZA customer service through their official webstrona: www.azza.com.