Wstęp
The Voxelab Aquila X2 is an upgraded 3D printer designed for ease of use and high-quality printing. It features a removable carborundum glass platform, fully open-source capabilities, and a resume printing function. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Aquila X2 3D printer.
Figure 1: Voxelab Aquila X2 3D Printer with a sampwydruk.
1. Instalacja i montaż
Proper assembly is crucial for optimal performance. Follow the steps below to set up your Voxelab Aquila X2 printer. For a visual guide, please refer to the official installation video.
1.1 Rozpakowywanie i identyfikacja komponentów
Carefully unbox all components and verify against the packing list. Ensure all parts are present and undamaged before proceeding with assembly.
Video 1: VOXELAB Aquila X2 Installation Video. This video provides a step-by-step guide for assembling the printer.
1.2 Z-axis and X-axis Assembly
Attach the Z-axis profiles to the base and then install the X-axis kit, ensuring all screws are tightened securely. The Z-axis limit switch profile should be on the left side of the printer.
Figure 2: The robust all-metal body of the Aquila X2, highlighting its structural components.
1.3 Screen and Spool Holder Installation
Mount the 4.3-inch color screen to the printer base and attach the filament spool holder to the top gantry profile. Ensure all cables are connected correctly.
Figure 3: The Aquila X2's new user interface displayed on its 4.3-inch color screen.
1.4 Podłączenie zasilania i pierwsze włączenie
Connect the power cord and ensure the voltage switch (115V/230V) is set correctly for your region before turning on the power switch. The printer will perform an auto-home sequence upon first power-on.
Figure 4: The carborundum glass platform, providing excellent adhesion and easy print removal.
2. Instrukcja obsługi
This section guides you through the basic operations of your Aquila X2 3D printer, from loading filament to starting your first print.
2.1 Ładowanie filamentu
Hang the filament spool on the material rack. Cut the end of the filament at an angle and insert it into the filament feeding port. Use the "Automatic Load" function from the Control menu on the screen to feed the filament until it extrudes evenly from the nozzle.
Figure 5: The filament detection sensor, which pauses prints when filament runs out.
Figure 6: The intelligent auto filament feed-in technology simplifies filament loading.
2.2 Poziomowanie łóżka
Accurate bed leveling is essential for successful prints. Use a piece of A4 paper between the nozzle and the print bed. Move the nozzle to each of the four corners and adjust the leveling nuts until you feel a slight resistance when moving the paper. The nozzle should just scratch the paper lightly.
2.3 Rozpoczęcie drukowania
Prepare your 3D model using a slicing software (e.g., Cura, PrusaSlicer) and save it to a TF card. Insert the TF card into the printer's slot. On the printer's screen, navigate to the "Print" menu, select your filei potwierdź, aby rozpocząć drukowanie.
Video 2: VOXELAB Upgraded Aquila X2 3D Printer. This video demonstrates the printer's features and operation.
Video 3: Voxelab Aquila X2 - Make Every Day Matter. A short overview of the printer's capabilities and user experience.
3. Konserwacja
Regularna konserwacja gwarantuje długowieczność i stałą wydajność Twojej drukarki 3D.
- Wyczyść platformę drukującą: After each print, allow the carborundum glass platform to cool down and then gently remove the print. Clean the surface with isopropyl alcohol to ensure good adhesion for future prints.
- Czyszczenie dysz: Periodically check the nozzle for clogs. Use the provided needle or perform a cold pull if necessary to clear any obstructions.
- Smarowanie ruchomych części: Co kilka miesięcy nanieś niewielką ilość smaru litowego na śrubę pociągową osi Z oraz pręty gładkie, aby zapewnić płynny ruch.
- Sprawdź paski: Ensure the X and Y-axis belts are properly tensioned. They should be taut but not overly tight.
4. Rozwiązywanie Problemów
Oto kilka typowych problemów i ich rozwiązań:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Wydruk nie przykleja się do łóżka | Bed not leveled, dirty bed, incorrect bed temperature. | Re-level the print bed. Clean the bed with isopropyl alcohol. Adjust bed temperature in slicing software. |
| Filament nie wytłacza się | Zatkana dysza, splątany filament, nieprawidłowa temperatura. | Clear nozzle clog. Untangle filament. Verify nozzle temperature. |
| Drukarka zatrzymuje się w połowie drukowania | Moc outage, filament run-out. | The Aquila X2 has a resume printing function; it should automatically resume. Check filament sensor for run-out. |
| Niska jakość druku | Incorrect print settings, worn nozzle, loose belts. | Adjust print speed, temperature, and retraction settings. Replace nozzle if worn. Check and tighten belts. |
5. Specyfikacje
| Specyfikacja | Wartość |
|---|---|
| Wymiary produktu | 22.44 x 14.96 x 8.46 cala |
| Waga przedmiotu | 2.2 funta (1 kilograma) |
| Numer modelu przedmiotu | Aquila X2 |
| Marka | Wokselab |
| Tworzywo | Carborundum, PLA |
| Kolor | Czarny |
| Data pierwszej dostępności | 17 kwietnia 2021 r. |
| Zgodne filamenty | PLA, ABS, PETG 1.75mm |
| Zbuduj platformę | Removable Carborundum Glass Platform |
| Płyta główna | 32-bit silent motherboard |
| Wyświetlacz | 4.3-calowy kolorowy ekran |
6. Gwarancja i wsparcie
Voxelab provides lifetime technical assistance for all its 3D printers. For any questions regarding product operation or software, please feel free to contact Voxelab customer support. Refer to the official Voxelab webstrona zawierająca najbardziej aktualne informacje dotyczące gwarancji i dane kontaktowe.
Voxelab is a subsidiary brand of Flashforge, a premium 3D printer manufacturer, ensuring reliable support and resources.
