Basen Intex 12' x 30" z metalową ramą, pompą filtrującą i zestawem konserwacyjnym – instrukcja obsługi

1. Wprowadzenie

This manual provides essential information for the safe and efficient setup, operation, and maintenance of your Intex 12' x 30" Metal Frame Swimming Pool. Please read all instructions carefully before assembly and use to ensure proper function and safety.

2. Informacje dotyczące bezpieczeństwa

OSTRZEŻENIE: Nieprzestrzeganie tych instrukcji może spowodować poważne obrażenia lub śmierć.

• Zawsze sprawuj nadzór nad dziećmi przebywającymi w basenie i wokół niego.
• Nie nurkuj ani nie skacz do basenu. Głębokość wody jest niewystarczająca do nurkowania.
• Upewnij się, że basen stoi na równej powierzchni. Nierówne powierzchnie mogą spowodować zapadnięcie się basenu.
• Keep electrical cords and equipment away from water.
• Install appropriate barriers around the pool to prevent unsupervised access by children.
• Regularly check all components for wear and tear. Replace damaged parts immediately.

3. Zawartość opakowania

Verify that all components listed below are present in your package. If any parts are missing or damaged, do not proceed with assembly and contact customer support.

• Intex 12' x 30" Metal Frame Pool Liner
• Metal Frame Components (horizontal beams, vertical legs, corner joints)
• Intex Filter Pump (Model 28603EG)
• Type "A" Filter Cartridge
• Węże i Clamps for Filter Pump Connection
• Intex Deluxe Pool Maintenance Kit (includes telescoping pole, vacuum head, skimmer net, wall brush)
• Instrukcja obsługi (ten dokument)

4. Konfiguracja

Proper site preparation and assembly are crucial for the stability and longevity of your pool.

4.1 Przygotowanie miejsca

1. Choose a firm, level area in your yard, free from sharp objects, debris, or loose soil.
2. Ensure the area is large enough to accommodate the pool and allow for safe access around it.
3. Avoid placing the pool under overhead power lines or near trees that may drop leaves and debris.
4. Clear any grass or vegetation from the chosen area. A ground cloth (not included) is recommended to protect the pool liner.

4.2 Montaż basenu

Follow these steps to assemble the metal frame pool. It is recommended to have at least two people for assembly.

1. Unfold the pool liner and spread it out in the prepared area. Ensure the drain plug is facing the desired drainage location.
2. Assemble the horizontal beams by sliding them through the sleeves at the top of the pool liner.
3. Connect the horizontal beams using the corner joints.
4. Insert the vertical legs into the T-joints of the frame. Ensure they are securely seated.
5. Attach the leg caps to the bottom of each vertical leg.

4.3 Podłączenie pompy filtrującej

Connect the filter pump to the pool as follows:

1. Identify the two openings on the side of the pool liner for the filter pump.
2. Attach the two hoses from the filter pump to these openings using the provided clamps. Upewnij się, że wszystkie połączenia są szczelne, aby zapobiec wyciekom.
3. Place the filter pump on a stable, level surface at least 10 feet away from the pool.

4.4 Napełnianie basenu

1. Begin filling the pool with water. As the water level rises, smooth out any wrinkles in the bottom of the liner.
2. Fill the pool to the recommended water level, typically indicated by a fill line on the liner or frame.

4.5 Przewodnik wideo po konfiguracji

For a visual guide on setting up your Intex Metal Frame Pool, please watch the official seller video below:

5. Instrukcja obsługi

The filter pump is essential for keeping your pool water clean and clear.

5.1 Działanie pompy filtrującej

1. Ensure the filter pump is properly connected to the pool and plugged into a grounded electrical outlet.
2. Open the air release valve on top of the filter pump to allow any trapped air to escape. Close it once water begins to flow out.
3. Turn on the filter pump. The pump should run for a minimum of 4-6 hours per day to ensure adequate water circulation and filtration. Adjust run time based on pool usage and water clarity.

6. Konserwacja

Regular maintenance is vital for extending the life of your pool and ensuring clean, safe swimming conditions.

6.1 Filter Cartridge Cleaning and Replacement

1. Przed przystąpieniem do prac konserwacyjnych należy wyłączyć pompę filtrującą i odłączyć ją od zasilania.
2. Unscrew the filter housing cap and remove the Type "A" filter cartridge.
3. Dokładnie wypłucz wkład wężem ogrodowym, aby usunąć zanieczyszczenia.
4. Replace the cartridge every 2 weeks or sooner if the water flow is reduced or the cartridge appears heavily soiled.

6.2 Chemia wodna

Test your pool water regularly (daily or every other day) using a pool test kit. Maintain the following levels:

• Chlor: 1-3 ppm (parts per million)
• pH: 7.4-7.6
• Zasadowość: 80-120 ppm

Adjust chemicals as needed according to product instructions.

6.3 Czyszczenie basenu

Use the included Deluxe Pool Maintenance Kit for routine cleaning:

• Skimming: Use the skimmer net to remove leaves, insects, and other floating debris from the water surface daily.
• Odkurzanie: Attach the vacuum head to the telescoping pole and connect it to the filter pump's suction side (refer to pump manual for specific connection). Vacuum the pool bottom to remove settled debris.
• Szczotkowanie: Use the wall brush to scrub the pool walls and floor, dislodging algae and dirt for the filter to capture.

6.4 Zimowanie (przechowywanie poza sezonem)

When temperatures drop below 45°F (7°C), it is recommended to drain, clean, and properly store your pool to prevent damage.

1. Drain the pool completely using the drain plug.
2. Clean the liner thoroughly with mild soap and water.
3. Disassemble the frame and allow all components to dry completely.
4. Store the liner and frame parts in a dry, protected area, away from extreme temperatures and pests.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

For warranty information, please refer to the documentation included with your product or visit the official Intex website. For technical support, replacement parts, or further assistance, please contact Intex customer service directly. Keep your purchase receipt and model number handy when contacting support.