Instrukcja obsługi bezprzewodowego dzwonka do drzwi AVANTEK CW-11

1. Wprowadzenie

Thank you for choosing the AVANTEK CW-11 Wireless Doorbell. This manual provides essential information for the proper installation, operation, and maintenance of your new doorbell system. Please read these instructions carefully before use and retain them for future reference.

Image 1.1: AVANTEK CW-11 Wireless Doorbell system, showing the compact transmitter and receiver units.

2. Informacje dotyczące bezpieczeństwa

• Nie wystawiaj urządzenia na działanie ekstremalnych temperatur ani bezpośredniego światła słonecznego.
• Keep the device away from water and high humidity. The transmitter is IP55 waterproof, but the receiver is for indoor use only.
• Nie próbuj samodzielnie demontować ani naprawiać urządzenia. Skontaktuj się z obsługą klienta, aby uzyskać pomoc.
• Trzymaj baterie poza zasięgiem dzieci. Zużyte baterie utylizuj prawidłowo.

3. Zawartość opakowania

• 1 x Wireless Transmitter (Doorbell Button)
• 1 x Plug-in Receiver (Chime Unit)
• 1 x bateria CR2 (wstępnie zamontowana w nadajniku)
• 2 x Śruby
• 2 x Kotwice
• 1 x dwustronna taśma klejąca
• 1 x śrubokręt

4. Koniec produktuview

The AVANTEK CW-11 Wireless Doorbell system consists of a battery-powered transmitter (doorbell button) and a plug-in receiver (chime unit). The receiver features 52 selectable melodies, 5 adjustable volume levels, and an LED indicator for visual alerts.

Image 4.1: The receiver unit, illustrating its features including 52 chimes, 5 volume levels, and an LED indicator.

Image 4.2: The compact size of both the transmitter and receiver, designed to not obstruct adjacent power sockets.

5. Instrukcje konfiguracji

5.1 Installing the Transmitter

The transmitter can be installed using either the provided double-sided adhesive tape or screws and anchor plugs.

Image 5.1: Visual guide for installing the transmitter using either adhesive tape or screws and anchor plugs.

Metoda A: Używanie dwustronnej taśmy klejącej

1. Dokładnie oczyść powierzchnię, na której chcesz zamontować produkt, aby była wolna od kurzu i wilgoci.
2. Peel off one side of the protective film from the double-sided adhesive tape and attach it to the back of the transmitter.
3. Peel off the other side of the protective film and firmly press the transmitter onto the cleaned surface for at least 30 seconds.

Method B: Using Screws and Anchor Plugs

1. Mark the desired mounting points for the transmitter on the wall.
2. Wywierć dwa otwory w zaznaczonych miejscach.
3. Insert the anchor plugs into the drilled holes.
4. Align the transmitter's mounting holes with the anchor plugs and secure it with the provided screws.

Ważny: To prevent signal interference, do not install the transmitter close to or on metal surfaces such as metal door frames or mailboxes.

5.2 Plugging in the Receiver

Plug the receiver into a standard electrical outlet in a location where the chime can be easily heard. The LED on the receiver will flash upon initial power-up.

5.3 Pairing the Doorbell System

The transmitter and receiver are pre-paired at the factory. If re-pairing is needed or if you add additional transmitters/receivers, follow these steps:

1. Podłącz odbiornik do gniazdka elektrycznego.
2. To enter pairing mode, hold down the Volume button on the receiver for 3 seconds. The LED on the receiver will flash.
3. Remove the battery insulating film from the transmitter (if not already done).
4. Press the Push button on the transmitter. Its LED will flash.
5. After successful pairing, the receiver will chime once, and the LEDs on both the receiver and transmitter will flash simultaneously.

6. Instrukcja obsługi

6.1 Zmiana melodii

The receiver offers 52 different melodies. Use the 'Next' and 'Previous' buttons on the side of the receiver to cycle through the available tunes. Press the doorbell button to preview the selected melody.

Image 6.1: The receiver offers a wide selection of melodies for personalization.

6.2 Regulacja głośności

There are 5 adjustable volume levels, with a maximum setting of 115 dB. Use the 'Volume' button on the side of the receiver to increase or decrease the sound level.

6.3 Tryb wyciszenia

To activate mute mode (0 dB), repeatedly press the 'Volume' button until the sound is off. In this mode, only the LED indicator will flash when the doorbell is pressed, providing a silent visual alert.

Image 6.2: The mute mode feature allows for silent notifications, ideal for quiet environments.

7. Konserwacja

7.1 Czyszczenie

Przetrzyj urządzenia miękką, suchą ściereczką. Nie używaj środków czyszczących o właściwościach ściernych ani rozpuszczalników.

7.2 Wymiana baterii (nadajnik)

The transmitter uses a CR2 battery with an estimated lifespan of 3 years. When the battery is low, the transmitter's LED may not light up or the signal range may decrease. To replace the battery:

1. Ostrożnie otwórz nadajnik casing using the provided screwdriver or a small flat-head screwdriver.
2. Wyjmij starą baterię CR2.
3. Włóż nową baterię CR2, zwracając uwagę na prawidłową biegunowość (+/-).
4. Zamknij casing bezpiecznie.

8. Rozwiązywanie Problemów

• Doorbell not chiming: Ensure the receiver is plugged in and powered. Check the transmitter battery. Re-pair the devices if necessary (refer to Section 5.3).
• Krótki zasięg sygnału: Ensure the transmitter is not installed on or near metal surfaces. Relocate the receiver to a more central position. Replace the transmitter battery.
• Ingerencja: The doorbell operates on a frequency that minimizes interference with other household devices. If interference occurs, try changing the melody or relocating the receiver.
• Funkcja pamięci: The device remembers your last melody and volume level after a power outage, so no need to reset settings.

9. Specyfikacje

10. Gwarancja i wsparcie

For warranty information or technical support, please refer to the contact details provided with your product packaging or visit the official AVANTEK webZachowaj paragon jako dowód zakupu.