1. Wprowadzenie
This manual provides comprehensive instructions for the BTF-LIGHTING 5M 5630 High-Density Flexible LED Strip. Please read this manual thoroughly before installation and use to ensure proper function and safety. This LED strip is designed for various indoor lighting applications, offering bright and efficient illumination.
Image 1.1: The BTF-LIGHTING 5M 5630 Natural White LED Strip, coiled for packaging.
2. Funkcje produktu
- High-quality 5630 SMD Top LEDs, 300 LEDs total (60 LEDs/meter), offering approximately 2 times the brightness of SMD5050 LEDs.
- Operates on DC 12V input voltage, ensuring low power consumption.
- The strip is cuttable every 3 LEDs along designated cut markers, allowing for customization without damaging the remaining sections.
- Features an IP30 rating, indicating it is not waterproof. Ideal for indoor residential and commercial lighting decoration.
- Easy and flexible installation with high-quality self-adhesive 3M backing, suitable for clean, dry, and flat surfaces.
- Long lifespan exceeding 50,000 hours.
3. Informacje dotyczące bezpieczeństwa
Adhering to these safety guidelines is crucial for safe operation and to prevent damage to the product or injury.
- Zasilanie: Always ensure the power supply is disconnected before installation, cutting, or any maintenance. Use only a compatible DC 12V power supply (not included). Do not connect directly to 220V/110V AC power.
- Wodoodporność: This product has an IP30 rating, meaning it is nie wodoodporny. Avoid exposure to moisture, water, or high humidity environments.
- Pochylenie się: Do not bend the LED strip sharply or at acute angles to prevent damage to the circuit board and LEDs. While flexible, excessive bending can cause component failure.
- Ciepło: Ensure adequate ventilation around the LED strip, especially when installed in enclosed spaces, to prevent overheating.
- Cięcie: Only cut the LED strip at the designated cut marks. Cutting elsewhere will damage the circuit and render that section unusable.
- Dzieci: Produkt i jego elementy należy przechowywać w miejscu niedostępnym dla dzieci.
4. Zawartość opakowania
Sprawdź, czy po otwarciu opakowania znajdują się wszystkie elementy:
- 1 x 5-meter BTF-LIGHTING 5630 Natural White LED Strip
Note: A DC 12V power supply and dimmer are not included and must be purchased separately.
5. Konfiguracja i instalacja
Follow these steps for proper installation of your LED strip:
- Przygotuj powierzchnię: Ensure the installation surface is clean, dry, and smooth. Dust, oil, or moisture can compromise the adhesive's effectiveness.
- Zmierz i tnij (opcjonalnie): If a shorter length is required, measure the desired length and cut the LED strip only at the designated cut marks (indicated by a copper pad and scissor icon). Each cut segment consists of 3 LEDs.
- Odklej i przymocuj: Carefully peel off the protective backing from the 3M adhesive tape on the back of the LED strip. Press the strip firmly onto the prepared surface, ensuring good contact along its entire length.
- Podłącz zasilanie: Connect the red wire of the LED strip to the positive (+) terminal of your DC 12V power supply and the black wire to the negative (-) terminal. Ensure correct polarity.
- Connect Dimmer (Optional): If using a dimmer, connect it between the power supply and the LED strip, following the dimmer's specific instructions.
- Test: Once all connections are secure, plug in the power supply to test the LED strip.
Image 5.1: Illustration of the LED strip's cuttable points, flexible FPCB design, and double-sided adhesive tape for installation.
Image 5.2: Visual guide demonstrating the two primary installation steps: cleaning the surface and then applying the LED strip.
6. Instrukcja obsługi
Operating the BTF-LIGHTING LED strip is straightforward:
- Włączanie/wyłączanie: Connect the 12V DC power supply to a power outlet to turn on the LED strip. Disconnect or use a switch on your power supply/dimmer to turn it off.
- Ściemnianie: If you have connected a compatible 12V DC dimmer (not included), use its controls to adjust the brightness level of the LED strip.
Obraz 6.1: Examples of the LED strip used in different indoor settings, including kitchen under-cabinet lighting, TV backlighting, stair lighting, and architectural accents.
7. Konserwacja
The BTF-LIGHTING LED strip requires minimal maintenance:
- Czyszczenie: Ensure the power is off before cleaning. Gently wipe the LED strip with a soft, dry cloth. Do not use abrasive cleaners or excessive moisture.
- Kontrola: Periodically check the strip for any signs of damage, loose connections, or adhesive degradation.
- Składowanie: Przechowując pasek, należy upewnić się, że jest luźno zwinięty i przechowywany w suchym, chłodnym miejscu, z dala od bezpośredniego światła słonecznego.
8. Rozwiązywanie Problemów
If you encounter issues with your LED strip, refer to the following common problems and solutions:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Taśma LED nie świeci. | No power, incorrect wiring, faulty power supply. | Check power connections, ensure correct polarity (+ to +, - to -). Test power supply with another device if possible. |
| Only a section of the strip lights up. | Damage to the circuit after a cut, faulty segment. | Inspect the cut area for damage. If a segment is faulty, it may need replacement or isolation. |
| LEDs are flickering. | Unstable power supply, loose connection, incompatible dimmer. | Ensure power supply is stable and sufficient. Check all connections. If using a dimmer, ensure it is compatible with 12V DC LED strips. |
| Klej nie trzyma. | Surface not clean/dry, unsuitable surface material. | Ensure surface is thoroughly cleaned and dried before application. For rough or porous surfaces, consider using additional mounting clips or stronger adhesive. |
9. Specyfikacje
Detailed technical specifications for the BTF-LIGHTING 5M 5630 LED Strip:
| Funkcja | Szczegół |
|---|---|
| Marka | OŚWIETLENIE BTF |
| Numer modelu | 56305MNW60W30N |
| Typ diody LED | SMD5630 |
| Diody LED na metr | 60 diody LED |
| Całkowita liczba diod LED | 300 diody LED |
| Długość paska | 5 metrów |
| FPCB Width | 10 mm |
| Wejście Voltage | Prąd stały 12 V |
| Pobór mocy | 0.1 W/LED (Total 30W for 5M) |
| Zalecany zasilacz | DC 12V 3A (or higher for longer strips) |
| Kolor światła | Natural White (approx. 4000K-4500K) |
| Moc wyjściowa | 23-25 lm/LED |
| Kąt wiązki | 120 stopnia |
| Temperatura pracy | -20℃ do 50℃ |
| Poziom ochrony | IP30 (nie wodoodporny) |
| Cuttable Interval | Co 3 diody LED |
| Długość życia | > 50,000 godzin |
Image 9.1: This image illustrates different color temperatures of LED strips. The product covered in this manual is Natural White (4000K-4500K).
10. Gwarancja i wsparcie
This BTF-LIGHTING LED strip comes with a 1-letnia gwarancja od daty zakupu, obejmując wady produkcyjne.
For technical support, warranty claims, or any questions regarding your product, please contact BTF-LIGHTING customer service through your retailer or the official BTF-LIGHTING website. Please have your model number (56305MNW60W30N) and proof of purchase ready when contacting support.
