MCP2200-I/SO USB to UART Serial Converter

1. Wprowadzenie

This manual provides essential information for the proper use, installation, and maintenance of the MICROCHIP MCP2200-I/SO USB to UART Serial Converter. The MCP2200 is a highly integrated circuit designed to provide a simple and cost-effective solution for adding USB connectivity to applications that traditionally use UART (Universal Asynchronous Receiver/Transmitter) communication.

Główne cechy obejmują:

• Data Rate: Up to 12 Mbps (USB Full-Speed)
• Number of Channels: 8 (GPIO pins configurable for various functions)
• Objętość dostawtage: 2.7 V do 5.5 V
• Zakres temperatury roboczej: -40 ° C do + 85 ° C
• Package: SOIC-20LD (Surface Mount Technology)

2. Koniec produktuview

The MCP2200-I/SO is a compact integrated circuit, typically black in color, with metal pins extending from its sides for surface mounting onto a printed circuit board (PCB). It acts as a bridge, converting data between a USB interface and a standard UART serial interface.

Rysunek 2.1: An image showing the black rectangular body of the MCP2200-I/SO integrated circuit with metal pins extending from both long sides, designed for surface mount applications. A small circular indentation marks pin 1, indicating orientation.

3. Konfiguracja i integracja

The MCP2200-I/SO is a surface-mount component requiring integration into a larger electronic circuit. Proper setup involves:

1. Projekt PCB: Design a printed circuit board (PCB) that accommodates the SOIC-20LD package. Ensure correct pin assignments for USB (D+, D-), UART (TX, RX), power (VCC, GND), and any desired GPIO functionality. Refer to the official Microchip datasheet for detailed pinout and recommended circuit diagrams.
2. Zasilanie: Provide a stable power supply within the specified range of 2.7 V to 5.5 V. Decoupling capacitors are recommended near the VCC pins to ensure stable operation.
3. Połączenie USB: Connect the USB D+ and D- pins to a standard USB connector (e.g., USB Type-B or Micro-USB) on your PCB. External pull-up resistors may be required depending on the USB host configuration.
4. UART Connection: Connect the UART TX and RX pins to the corresponding UART interface of your target microcontroller or device. Ensure voltage level compatibility.
5. Instalacja sterownika: Once the hardware is assembled and connected to a computer via USB, the necessary drivers for the MCP2200 will typically be installed automatically by modern operating systems. If not, drivers can be downloaded from the official Microchip webstrona.

Notatka: This device is intended for integration by experienced electronics engineers. Refer to the complete datasheet for detailed electrical characteristics and application notes.

4. Działanie

Once the MCP2200-I/SO is correctly integrated into a circuit and connected to a host computer via USB, it will enumerate as a standard COM port. This allows software applications on the host computer to communicate with a UART device connected to the MCP2200's serial pins.

• Komunikacja szeregowa: Use any standard serial terminal program (e.g., PuTTY, Tera Term, Arduino Serial Monitor) or custom software to open the virtual COM port associated with the MCP2200.
• Konfiguracja szybkości transmisji: Configure the baud rate, data bits, parity, and stop bits in your software to match the settings of the UART device connected to the MCP2200. The MCP2200 supports common baud rates.
• Przepływ danych: Data sent from the host computer to the virtual COM port will be converted by the MCP2200 and transmitted via its UART TX pin. Data received on the UART RX pin will be converted and sent back to the host computer via USB.
• Sterowanie GPIO: The MCP2200 also features 8 General Purpose Input/Output (GPIO) pins. These can be configured and controlled via specific USB commands or through a dedicated utility provided by Microchip, allowing for additional control over the connected device.

5. Konserwacja i pielęgnacja

The MCP2200-I/SO is a robust integrated circuit designed for long-term operation. Minimal maintenance is required, but adherence to the following guidelines will ensure optimal performance and longevity:

• Warunki środowiskowe: Operate the device within its specified operating temperature range (-40°C to +85°C) and avoid exposure to excessive humidity, dust, or corrosive substances.
• Stabilność zasilania: Zapewnij czyste i stabilne zasilanie. Tomtagwahania lub przekroczeniatage can damage the component.
• Obsługa fizyczna: Handle the IC with care during assembly to prevent damage to the pins or the package. Use anti-static precautions when working with electronic components.
• Czyszczenie: W razie konieczności czyszczenia należy usunąć kurz miękką, suchą szczotką lub sprężonym powietrzem. Unikaj płynnych środków czyszczących, chyba że są one przeznaczone specjalnie do urządzeń elektronicznych i stosuj je oszczędnie.

6. Rozwiązywanie Problemów

If you encounter issues with the MCP2200-I/SO, consider the following troubleshooting steps:

• Urządzenie nie jest rozpoznawane przez komputer:
  • Sprawdź połączenie kabla USB.
  • Check power supply to the MCP2200.
  • Ensure correct driver installation. Check Device Manager for unrecognized devices or COM ports.
  • Test with a different USB port or computer.
• Brak transmisji/odbioru danych:
  • Confirm correct UART TX/RX connections between MCP2200 and target device (TX to RX, RX to TX).
  • Verify baud rate, data bits, parity, and stop bits settings in your serial terminal software match the target device.
  • Sprawdź objętośćtage levels on UART lines for compatibility.
  • Ensure the target device is powered on and functioning correctly.
• Komunikacja przerywana:
  • Check for loose connections or cold solder joints on the PCB.
  • Ensure adequate power supply stability; add or check decoupling capacitors.
  • Minimize electrical noise in the environment.

For more advanced troubleshooting, consult the official Microchip MCP2200 datasheet and application notes.

7. Specyfikacje techniczne

8. Gwarancja i wsparcie

As an electronic component, the MCP2200-I/SO is typically covered by the manufacturer's standard warranty for integrated circuits. For specific warranty terms and conditions, please refer to the official documentation provided by MICROCHIP TECHNOLOGY or visit their official webstrona.

For technical support, datasheets, application notes, and driver downloads, please visit the official MICROCHIP TECHNOLOGY website. You may also contact their customer support for assistance with product-related inquiries.

Producent: TECHNOLOGIA MIKROCHIPÓW

Product Page (Amazon): View on Amazon.com