Instrukcja obsługi programowalnego loopera One Control OC10 Crocodile Tail Loop

1. Wprowadzenie

The One Control OC10 Crocodile Tail Loop is a highly versatile programmable looper designed for guitar effects pedalboards. It allows musicians to create complex signal chains and recall them instantly, enhancing performance flexibility and sound management.

This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your OC10 Crocodile Tail Loop.

2. Główne cechy

10 Switchable Effects Loops: Provides extensive options for pedalboard configuration.
Series and Independent Loops: Loops 1-7 operate in series from a single main input, while loops 8, 9, and 10 feature independent external inputs for advanced routing.
Tryb bezpośredni: Allows individual toggling of loops via dedicated footswitches.
Integracja MIDI: Enables control and synchronization with MIDI-compatible devices.
Kompaktowa konstrukcja: Optimized for pedalboard space efficiency.

3. Zawartość opakowania

Sprawdź, czy w opakowaniu znajdują się wszystkie elementy:

One Control OC10 Crocodile Tail Loop Unit
Power Adapter (if included in bundle)
4 x Patch Cables (as per bundle description)
Instrukcja obsługi (ten dokument)

One Control OC10 Crocodile Tail Loop with included cables

Rycina 3.1: Przód view of the One Control OC10 Crocodile Tail Loop with included patch cables. The unit is black with silver footswitches and a central silver handle. Two short patch cables and two longer patch cables are visible above the unit.

4. Konfiguracja i połączenia

Proper connection of the OC10 is crucial for optimal performance. Follow these steps to integrate the looper into your setup.

4.1 Połączenie zasilania

Connect the appropriate 9V DC power adapter (center negative) to the "9V IN" jack on the rear panel of the OC10. Ensure the power source meets the specified voltagi aktualnych wymagań.

4.2 Połączenia audio

The OC10 features multiple input and output jacks for flexible routing.

Tył view of One Control OC10 Crocodile Tail Loop showing all input and output jacks

Figure 4.1: Rear panel of the One Control OC10 Crocodile Tail Loop, displaying various input, output, send, and return jacks for effects loops, MIDI IN/OUT/THRU, and power input.

Główne wejście: Connect your guitar or the output of your first pedal to the "IN" jack.
Główne wyjście: Connect the "OUT-1" jack to your amplifier's input or the next device in your signal chain.
Effects Loops (1-7): For each loop, connect the "SEND" jack to the input of your effect pedal and the "RETURN" jack to the output of the same pedal. These loops are in series.
Independent Loops (8, 9, 10): These loops have dedicated "IN" and "OUT" jacks (e.g., IN8, OUT8). Use these for effects that require a separate input or for parallel routing.
Wyjście tunera: Connect your tuner to the "TUNER" jack. This output is buffered.

4.3 Połączenia MIDI

The OC10 supports MIDI for advanced control and integration with other MIDI-enabled devices.

Wejście MIDI: Connect a MIDI controller or interface here to send program change (PC) or control change (CC) messages to the OC10.
WYJŚCIE/PRZEJŚCIE MIDI: Use "MIDI OUT" to send MIDI messages generated by the OC10. "MIDI THRU" passes incoming MIDI data directly to another device.

5. Instrukcja obsługi

The OC10 offers various modes of operation to suit different performance needs.

Szczyt view of One Control OC10 Crocodile Tail Loop showing footswitches and control buttons

Figure 5.1: Top panel of the One Control OC10 Crocodile Tail Loop, highlighting the footswitches for program selection and bank changes, along with the smaller control buttons for programming and MIDI settings.

5.1 Tryb programu

In Program Mode, you can store and recall combinations of activated effects loops. Each program saves the on/off state of all 10 loops.

Wybór programów: Use the footswitches labeled PGM1/L1 through PGM7/L7 to select a stored program. The active program's LED will illuminate.
Zmiana banku: Use the "BANK UP/L8" and "BANK DN/L9" footswitches to navigate through different banks of programs.
Storing Programs:
1. Activate or deactivate the desired loops using the small buttons above the footswitches (or in Direct Mode).
2. Press and hold the footswitch where you want to save the program until its LED flashes, indicating successful storage.

5.2 Tryb bezpośredni

Direct Mode allows you to individually toggle each of the 10 effects loops on or off in real-time, without recalling a stored program.

Activating Direct Mode: Press the "DIRECT" button (usually near the tuner output switch). The "DIRECT" LED will illuminate.
Toggling Loops: In Direct Mode, each footswitch (PGM1/L1 to PGM7/L7, BANK UP/L8, BANK DN/L9, TUNER/L10) directly controls its corresponding loop. Press the footswitch to toggle the loop on or off.

5.3 Obsługa MIDI

The OC10 can send and receive MIDI Program Change (PC) and Control Change (CC) messages.

Receiving PC Messages: The OC10 can be configured to switch programs based on incoming MIDI PC messages. Refer to the detailed MIDI section in the full manual for mapping.
Sending PC/CC Messages: The OC10 can be programmed to send MIDI PC or CC messages when a program is recalled or a loop is toggled. This allows it to control other MIDI-compatible devices in your setup.

6. Konserwacja

To ensure the longevity and optimal performance of your OC10 Crocodile Tail Loop, follow these maintenance guidelines:

Czyszczenie: Do przecierania urządzenia używaj miękkiej, suchej ściereczki. Unikaj środków czyszczących o właściwościach ściernych i rozpuszczalników.
Składowanie: Przechowywać urządzenie w chłodnym, suchym miejscu, z dala od bezpośredniego światła słonecznego i ekstremalnych temperatur.
Znajomości: Periodically check all cable connections for secure fit and signs of wear. Loose connections can cause signal loss or noise.
Zasilanie: Always use the specified power supply. Incorrect voltagZła biegunowość może spowodować uszkodzenie urządzenia.

7. Rozwiązywanie Problemów

If you encounter issues with your OC10, refer to the following common problems and solutions:

Problem	Możliwa przyczyna	Rozwiązanie
Brak zasilania/Urządzenie się nie włącza	Incorrect power supply; Loose power connection; Faulty outlet	Ensure correct 9V DC (center negative) power supply is used. Check power cable connection. Test outlet with another device.
No sound/Signal loss	Incorrect cable connections; Faulty cables; Loop not activated; Buffer issue	Verify all audio cables are correctly connected to IN/OUT/SEND/RETURN jacks. Test cables. Ensure the desired loop is active in Program or Direct Mode. Check buffer settings.
Buczenie lub hałas	Ground loop; Faulty power supply; Interference from other devices	Use isolated power supply for pedals. Ensure proper grounding. Move unit away from power transformers or noisy electronics.
Programs not saving	Nieprawidłowa procedura zapisywania	Ensure you press and hold the target footswitch until the LED flashes to confirm saving.

If the problem persists after trying these solutions, please contact One Control customer support.

8. Specyfikacje

Funkcja	Szczegół
Model	OC10 Crocodile Tail BUNDLE
Wymiary (dł. x szer. x wys.)	24 x 18 x 8 cali (w przybliżeniu, na podstawie wymiarów produktu)
Waga	17.3 funta
Zasilacz	9 V DC (środek ujemny)
Effects Loops	10 (7 series, 3 independent)
MIDI	MIDI IN, MIDI OUT/THRU
Kolor	Czarny
Interfejs sprzętowy	Dźwięk 1/4 cala
Format sygnału	Analog

9. Gwarancja i wsparcie

One Control products are designed for reliability and performance. For warranty information and technical support, please refer to the official One Control webodwiedź witrynę lub skontaktuj się z autoryzowanym dealerem.

Obsługa klienta: For assistance with product setup, operation, or troubleshooting, please visit the One Control Support Page lub skontaktuj się bezpośrednio z ich obsługą klienta.

Plany ochrony: Additional protection plans may be available for purchase. Please check with your retailer for details on extended warranty options.

	Instrukcja obsługi pętli krokodylkowej One Control Instrukcja obsługi One Control Crocodile Tail Loop, flagowego programowalnego przełącznika pedałowego z obsługą MIDI i wbudowanym buforem BJF.
	Instrukcja obsługi pętli stereo MIDI Dual Stereo Loop firmy One Control z serii Minimal Detailed user manual for the One Control Minimal Series MIDI Dual Stereo Loop (MDSL) pedal. Learn about its MIDI loop functionality, stereo/mono capabilities, specifications, MIDI signal control commands (PC and CC), and L1/L2 switch settings for managing mono-to-stereo signal conversion. The MDSL offers compact design and sophisticated functionality for guitarists and musicians.
	One Control Chamaeleo Tail Loop MK2 User Manual User manual for the One Control Chamaeleo Tail Loop MK2, a programmable guitar effects loop switcher with 5 loops, buffer, and intuitive controls.
	Agamidae Tail Loop User Manual User manual for the One Control Agamidae Tail Loop, detailing its features, operation, and technical specifications for managing guitar effects pedals.
	Jedna kontrolka Minimal Series Black Loop z buforem BJF: Produkt ponadview i Specyfikacje Discover the One Control Minimal Series Black Loop, a versatile loop switcher with an integrated BJF-buffer, offering true bypass or buffered operation and dual DC outputs for guitar effects setups. Learn about its features, specifications, and the advanced functionality of the Minimal Series.
	Gebruikershandleiding Chamaeleo Tail Loop MKIII - jedno sterowanie Gebruikershandleided dla One Control Chamaeleo Tail Loop MKIII, kompaktowy 5-programowy przełącznik pętli z 4 pętlami szeregowymi, 1 oddzielną pętlą, wyciszeniem/wyjściem tunera i buforem BJF umożliwiającym efektywne routing sygnału.

One Control OC10 Crocodile Tail BUNDLE