Wstęp
The KING HWP120 is an advanced electronic line voltage programmable thermostat designed specifically for hydronic heating systems. This thermostat offers precise temperature control and energy savings through its 7-day independent programming capabilities, allowing for up to four time and temperature settings per day. Its user-friendly design features an illuminated LCD display and simple two-button operation for setting temperature and navigating menus. The HWP120 is equipped with memory backup to retain settings during power outages, ensuring consistent comfort.
Rysunek 1: Kątowy view of the KING HWP120 Electronic Line Voltage Programmable Hydronic System Thermostat, showing its white casing and green illuminated LCD display.
Informacje dotyczące bezpieczeństwa
OSTRZEŻENIE: To prevent electric shock or damage to the thermostat, disconnect power to the heating system at the main fuse or circuit breaker box before installation or servicing. This thermostat operates on line voltage (120V/240V) and requires careful handling. Installation should only be performed by a qualified electrician in accordance with local electrical codes.
- Always turn off power at the circuit breaker before working with electrical wiring.
- Upewnij się, że wszystkie połączenia przewodów są bezpieczne i odpowiednio izolowane.
- Do not exceed the specified electrical ratings of the thermostat (12.5 amps / 120 volts, 3000 watts / 240 volts).
- Trzymaj termostat z dala od wody i nadmiernej wilgoci.
Instalacja i konfiguracja
Proper installation is crucial for the safe and efficient operation of your HWP120 thermostat. It is recommended that a licensed electrician perform the installation.
Miejsce montażu
Choose a location on an interior wall, approximately 5 feet (1.5 meters) above the floor, away from direct sunlight, drafts, or heat sources (e.g., lamps, appliances, fireplaces). These factors can affect the thermostat's temperature readings.
Instrukcje okablowania
- Odłącz zasilanie: Turn off the power to your heating system at the main circuit breaker. Verify power is off before proceeding.
- Usuń stary termostat: Carefully remove your existing thermostat from the wall. Note the wiring connections.
- Podłącz okablowanie: Connect the wires from your heating system to the appropriate terminals on the HWP120 thermostat. Refer to the wiring diagram provided with your thermostat's packaging for specific connections. Ensure all connections are tight.
- Montaż termostatu: Secure the HWP120 thermostat to the wall using the provided mounting screws.
- Przywróć zasilanie: Po zakończeniu instalacji i zabezpieczeniu wszystkich połączeń należy przywrócić zasilanie za pomocą wyłącznika automatycznego.
Rycina 2: Przód view of the KING HWP120 Thermostat, highlighting the LCD display and the two control buttons below it.
Instrukcja obsługi
The HWP120 thermostat is designed for straightforward operation using its two primary buttons and illuminated LCD display.
Wyświetl ponadview
The LCD display shows the current room temperature, the set temperature, the time, day of the week, and the active program period (P1, P2, P3, P4). When the heating system is active, a "HEAT" indicator will typically be visible.
Rysunek 3: Bok pod kątem view of the KING HWP120 Thermostat, showing the ventilation grilles on the side and the clear display.
Adjusting Temperature Manually
To temporarily adjust the temperature, press the Up (▲) Lub W dół (▼) buttons. The display will show the new set temperature. This manual override will typically remain active until the next programmed period begins.
Ustawianie czasu i dnia
Refer to the detailed programming section for initial setup of time and day, as these are integral to the programming functions.
Instrukcje programowania
The HWP120 allows for 7 independent day programming with 4 times and temperature settings (P1, P2, P3, P4) per day. This feature helps optimize energy consumption by adjusting heating based on your schedule.
Wejście w tryb programowania
To enter programming mode, press and hold both the Up (▲) I W dół (▼) buttons simultaneously for a few seconds until the display changes to indicate programming mode (e.g., flashing time or day).
Ustawianie czasu i dnia
- In programming mode, the hour will typically flash. Use the Up or W dół przyciski do regulacji godziny.
- Press one of the buttons (e.g., Up or W dół, depending on the model's specific navigation) to advance to minutes, then adjust.
- Continue to advance to set the day of the week.
Setting Program Periods (P1-P4)
For each day of the week, you can set four distinct periods:
- P1 (Wake): Typically for morning, when you wake up.
- P2 (Leave): For when you leave home.
- P3 (Return): For when you return home.
- P4 (Sleep): For nighttime.
- While in programming mode, navigate to the desired day (e.g., Monday).
- Select P1. Set the desired start time and temperature for P1 using the Up or W dół pikolak.
- Advance to P2 and repeat the process for its start time and temperature.
- Continue for P3 and P4.
- Repeat this process for each day of the week (Tuesday through Sunday).
- Wychodzenie z trybu programowania: Once all settings are complete, the thermostat will typically exit programming mode automatically after a period of inactivity, or you may need to press and hold the buttons again to save and exit. Consult the full manual for specific exit procedures.
Ważna uwaga: The HWP120 thermostat initiates heating at the programmed time to reach the set temperature. It does not anticipate heating. Therefore, if you desire a room to be at a specific temperature by a certain time, set the program to begin heating approximately 15-30 minutes prior to that desired time, depending on your system's response time.
Konserwacja
The KING HWP120 thermostat requires minimal maintenance to ensure optimal performance.
- Czyszczenie: Okresowo przecieraj zewnętrzną część termostatu miękką, miękką szmatką.amp ściereczką. Nie używaj środków czyszczących o właściwościach ściernych ani rozpuszczalników, ponieważ mogą one uszkodzić wykończenie lub elementy wewnętrzne.
- Usuwanie kurzu: Ensure the ventilation slots on the thermostat casing remain clear of dust and debris to allow for proper air circulation and accurate temperature sensing.
- Moctage: The thermostat features memory backup for power outages, retaining your programmed settings. No action is typically required after a power restoration.
Rozwiązywanie problemów
If you encounter issues with your HWP120 thermostat, refer to the following common problems and solutions:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Wyświetlacz termostatu jest pusty. | Brak zasilania termostatu. | Check the circuit breaker for your heating system. Ensure it is in the "ON" position. Verify wiring connections. |
| Heating system not turning on/off as programmed. | Incorrect programming; manual override active; system malfunction. | Review your program settings carefully. Ensure no manual override is active. Check your heating system for other issues. |
| Room temperature inaccurate. | Na lokalizację termostatu mogą mieć wpływ przeciągi i źródła ciepła. | Ensure the thermostat is not exposed to direct sunlight, drafts from windows/doors, or heat from appliances. |
| Trudności w programowaniu. | Unfamiliarity with programming sequence. | Carefully re-read the "Programming Instructions" section. Practice the steps without making permanent changes. |
If problems persist after attempting these solutions, contact a qualified electrician or KING customer support for assistance.
Specyfikacje
| Funkcja | Szczegół |
|---|---|
| Nazwa modelu | HWP120 |
| Marka | KRÓL |
| Tomtage | 120 V / 240 V |
| Ampwymazać | 12.5 amps (120 V) / 12.5 amp(240V) |
| Cotage | 1500 watów (120 V) / 3000 watów (240 V) |
| Zakres temperatur | od 44°F do 95°F (od 7°C do 35°C) |
| Dokładność | ± 1.2°F @ 10 amps, ± .9°F @ 4.2 amps |
| Programowanie | 7 independent day programming with 4 times and temperature settings per day |
| Typ wyświetlacza | Cyfrowy, podświetlany wyświetlacz LCD |
| Typ sterowania | Naciśnij przycisk |
| Tworzywo | Plastikowy |
| Wymiary (dł. x szer. x wys.) | 4.88 x 3.13 x 2 cala |
| Waga przedmiotu | 10.4 uncji |
Gwarancja i wsparcie
Informacje o gwarancji
The KING HWP120 Electronic Line Voltage Programmable Hydronic System Thermostat comes with a 1-roczna ograniczona gwarancja from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For specific terms and conditions, please refer to the warranty documentation included with your product or visit the manufacturer's official webstrona.
Obsługa klienta
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact KING customer support. You can typically find contact information (phone number, email, or support portal) on the manufacturer's webmiejscu lub w opakowaniu produktu.
It is recommended to have your product model number (HWP120) and date of purchase available when contacting support.
