Wstęp
The Linear ACT-31B 1-Channel Keychain Transmitter is designed for use with Linear Access MegaCode receivers and controllers. This compact device provides convenient remote access, operating on a frequency of 318 MHz. It is equipped with a single channel for activation and includes two 2016-type Lithium batteries for immediate use. Its design focuses on portability and ease of integration with compatible Linear systems.
Produkt ponadview
Figure 1: Linear Act-31B 1-Channel Keychain Transmitter. This image displays the black, oval-shaped keychain transmitter with a single gray circular button on its face. It is attached to a metal split key ring via a black plastic quick-disconnect mechanism, highlighting its compact and portable design.
Główne cechy:
- MegaCode Format: Factory-programmed to support over 1 million unique codes, ensuring high security.
- Praca jednokanałowa: Designed for straightforward control of one compatible Linear access device.
- Częstotliwość pracy: Functions at 318 MHz for reliable signal transmission.
- Kompaktowa konstrukcja: Features a quick-disconnect key ring for easy attachment to keys or other items.
- Źródło zasilania: Powered by two 2016-type Lithium batteries (included).
Organizować coś
To set up your Linear ACT-31B Keychain Transmitter with a compatible Linear Access MegaCode receiver or garage door opener, follow these steps:
- Znajdź przycisk Dowiedz się: On your Linear garage door opener unit (typically mounted on the ceiling), locate the 'LEARN' button. This button is usually small and may be red or another color, often accompanied by an LED indicator.
- Aktywuj tryb nauki: Press and release the 'LEARN' button on your garage door opener. The LED indicator light on the opener should illuminate or flash, indicating that the unit is now in learn mode and ready to accept a new remote code.
- Program the Transmitter: Within approximately 30 seconds of activating the learn mode on the opener, press the button on your ACT-31B Keychain Transmitter. Hold the button down for a few seconds. The LED light on the garage door opener should blink or turn off, confirming that the transmitter has been successfully programmed.
- Operacja testowa: Release the button on the transmitter. Wait a few seconds, then press the button again to test if the garage door responds. If the door opens or closes, the programming was successful.
If the transmitter does not work after following these steps, refer to the troubleshooting section or the full installation manual for your specific garage door opener model.
Instrukcja obsługi
The Linear ACT-31B is a single-channel transmitter, meaning it controls one device. To operate your garage door or compatible Linear access device:
- Aktywacja: Simply press and release the single gray button on the face of the transmitter.
- Zakres: The transmitter has a maximum operating range of approximately 10 meters (33 feet). Optimal performance is achieved within this range, though environmental factors can affect signal strength.
- Częstotliwość: The device transmits on a 318 MHz frequency. Ensure your receiver is compatible with this frequency.
Konserwacja
Wymiana baterii:
The ACT-31B transmitter uses two 2016-type Lithium batteries. If the transmitter's range decreases significantly or it stops responding, the batteries may need replacement.
- Otwórz Casing: Ostrożnie otwórz nadajnik casing. This may involve gently prying it open along the seam with a small flat-head screwdriver or similar tool.
- Wyjmij stare baterie: Note the orientation of the existing batteries (+/-). Remove the old 2016-type Lithium batteries.
- Włóż nowe baterie: Insert two new 2016-type Lithium batteries, ensuring they are correctly oriented according to the polarity markings inside the casing.
- Zamknij Casing: Pstryknij casinz powrotem bezpiecznie razem.
After replacing the batteries, it may be necessary to re-program the transmitter to your garage door opener if it does not respond immediately. Refer to the 'Setup' section for programming instructions.
Rozwiązywanie problemów
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Nadajnik nie działa. | Wyczerpane lub słabe baterie. | Replace the two 2016-type Lithium batteries. |
| Transmitter has reduced range. | Weak batteries or environmental interference. | Replace batteries. Ensure no large metal objects or strong radio signals are blocking the path. |
| Transmitter was working, now it isn't. | Loss of programming or incompatible receiver. | Re-program the transmitter following the 'Setup' instructions. Verify your garage door opener is a Linear Access MegaCode compatible model. |
| Must press button repeatedly for it to work. | Intermittent signal or weak connection. | Check battery strength. Ensure the transmitter is within optimal range. Re-program if necessary. |
Specyfikacje
- Numer modelu: AKT-31B
- Wymiary produktu: 0.48 x 1.25 x 2.25 cala
- Waga przedmiotu: 0.48 uncji
- Kolor: Czarny
- Baterie: 2 Lithium Metal batteries (2016-type) required (included)
- Technologia łączności: Częstotliwość radiowa
- Częstotliwość pracy: 318MHz
- Maksymalny zasięg: 10 metrów (około 33 stóp)
- Cechy szczególne: Ergonomiczny, lekki
- Zgodne urządzenia: Linear Access MegaCode receivers and controllers
- Producent: Linear / Nortek
- Zawartość pudełka: Key Chain Transmitter (1 Channel)
Gwarancja i wsparcie
For specific warranty information regarding your Linear ACT-31B 1-Channel Keychain Transmitter, please refer to the documentation included with your purchase or contact Linear customer support directly. Warranty terms may vary.
Additional support resources, including detailed installation and user manuals, are available:
- Instrukcja instalacji (PDF): View Instrukcja instalacji
- Instrukcja obsługi (PDF): View Instrukcja obsługi
For technical assistance or further inquiries, please contact Linear customer service.
