Leviton 830-T 30 Amp, 125 Volt, Travel Trailer Vinyl Grounding Angle Plug User Manual

Wstęp

This manual provides comprehensive instructions for the safe and effective use of your Leviton 830-T 30 Amp, 125 Volt, Travel Trailer Vinyl Grounding Angle Plug. This commercial-grade, straight blade, angle, grounding plug is designed for reliable electrical connections in travel trailer applications. Please read all instructions carefully before installation and use.

Image: The Leviton 830-T Travel Trailer Vinyl Grounding Angle Plug, showing its compact, black vinyl construction and angled design.

Ważne informacje dotyczące bezpieczeństwa

OSTRZEŻENIE: Ten produkt może narazić Cię na działanie substancji chemicznych, w tym ołowiu, który jest znany w stanie Kalifornia jako czynnik powodujący raka i wady wrodzone lub inne szkody reprodukcyjne. Aby uzyskać więcej informacji, przejdź do www.P65Warnings.ca.gov.

• Always disconnect power before installing or servicing electrical components.
• Upewnij się, że wszystkie połączenia przewodów są solidne i zgodne z lokalnymi przepisami elektrycznymi.
• Nie używaj tego produktu, jeśli wydaje się uszkodzony.
• This plug is designed for 30 Amp, 125 Volt applications. Do not exceed these ratings.
• Keep away from water and moisture unless specifically rated for wet conditions.

Konfiguracja i instalacja

The Leviton 830-T plug requires assembly to connect to your electrical cable. Follow these steps carefully:

1. Przygotuj kabel: Strip the outer jacket of your electrical cable to expose the insulated wires (typically hot, neutral, and ground). Strip approximately 3/4 inch of insulation from each individual wire.
2. Zdemontuj wtyczkę: Carefully open the plug housing. Note that the internal blades may be shipped loose. Identify the terminal screws for each connection.
3. Podłącz przewody: Insert the stripped ends of the wires into the appropriate terminal openings. The deep-slotted, backed-out terminal screws are designed to securely clamp over stripped leads.
   • Połącz Gorący wire (usually black) to the brass-colored terminal.
   • Połącz Neutralny wire (usually white) to the silver-colored terminal.
   • Połącz Grunt wire (usually green or bare copper) to the green-colored terminal.
4. Bezpieczne połączenia: Tighten the terminal screws firmly to ensure maximum conductivity and prevent loose connections. Verify that no stray wire strands are touching other terminals.
5. Ponowny montaż obudowy: Carefully position the internal components and blades, then close the plug housing. Ensure all parts fit correctly and the housing is securely fastened.

Obraz: Tył view of the Leviton 830-T plug, illustrating the terminal screws for hot, neutral, and ground wire connections. Note the "MEXICO 30A - 125V" marking.

Note: Some users have reported that the blades may not be permanently installed and the wire clamps can be challenging for stranded wire. Take extra care during assembly to ensure proper and secure connections.

Instrukcja obsługi

Once assembled, the Leviton 830-T plug is ready for use:

1. Ensure the power source (e.g., RV park pedestal) is turned OFF before plugging in or unplugging.
2. Insert the plug firmly into a compatible 30 Amp, 125 Volt NEMA TT-30R receptacle.
3. Once fully inserted, you may turn ON the power at the source.
4. To disconnect, first turn OFF the power at the source, then firmly grasp the plug body and pull it straight out from the receptacle. Do not pull by the cord.

Konserwacja

• Periodically inspect the plug for any signs of wear, cracks, or damage to the housing or blades.
• Check the cable entry point for fraying or damage.
• Ensure terminal screws remain tight. Re-tighten if necessary, with power disconnected.
• Clean the plug exterior with a dry, soft cloth. Do not use harsh chemicals or abrasive cleaners.
• Przechowuj wtyczkę w czystym i suchym miejscu, gdy jej nie używasz.

Rozwiązywanie problemów

• Brak zasilania:
  • Check if the power source (e.g., circuit breaker at the pedestal) is ON.
  • Verify that the plug is fully inserted into the receptacle.
  • Inspect the cable and plug for any visible damage.
  • Ensure internal wiring connections are secure (refer to Setup section).
• Plug Does Not Fit into Receptacle (e.g., "mousehole"):
  • Confirm the receptacle is a NEMA TT-30R type.
  • Some RV "mouseholes" or access points may have limited space. Compare the dimensions of the plug (4.1 x 3.9 x 2.5 inches) with the available space. Minor modifications to the access point cover may be required in some cases, but always ensure safety and weather sealing.
• Difficulty Assembling Wires:
  • Ensure wires are stripped to the correct length (approx. 3/4 inch).
  • Twist stranded wires tightly before inserting them into the terminal clamps to prevent fraying.
  • Confirm the blades are correctly seated within the housing before attempting to close.

Specyfikacje

Gwarancja i wsparcie

This Leviton 830-T plug is covered by a 10 rok ograniczonej gwarancji. For warranty claims, technical support, or further assistance, please contact Leviton customer service. You can find contact information and additional resources on the official Leviton webstrona: www.leviton.com.