Geeekpi Low-Profile Plus CPU Cooler for Raspberry Pi 5

1. Koniec produktuview

The Geeekpi Low-Profile Plus CPU Cooler (Model EP-0226) is an advanced cooling solution specifically designed for the Raspberry Pi 5. It features a dual-copper-pipe design, aluminum fins, and an integrated fan to efficiently dissipate heat and maintain optimal operating temperatures for your Raspberry Pi 5. This cooler is an evolution of the Ice Tower Cooler, offering enhanced thermal performance in a compact form factor.

Figure 1: Geeekpi Low-Profile Plus CPU Cooler installed on a Raspberry Pi 5.

Główne cechy:

• High-Efficiency Cooling: Advanced dual-pipe design for superior thermal conductivity.
• Aluminum Fins: Increased surface area for improved heat dissipation.
• Direct Heat Exhaust Fan: Designed to rapidly expel heat away from the processor.
• Kompaktowa konstrukcja: Ideal for small form factor applications.
• Zgodność: Specifically designed for Raspberry Pi 5.
• Cicha praca: Optimized fan design for a low-noise cooling experience (below 28 dB(A)).

2. Zawartość opakowania

Sprawdź, czy wszystkie wymienione poniżej elementy znajdują się w Twojej paczce. Jeśli brakuje któregokolwiek z nich lub jest on uszkodzony, skontaktuj się ze sprzedawcą.

Figure 2: All components included in the package. (Raspberry Pi is NOT included)

• 1 x Low-Profile Plus CPU Cooler
• 4 x M2.5*6+4mm Hand-tightened copper nuts
• 4 śruby M2.5*6mm
• 4 x M2.5*10mm Hexagon screws
• 1 x Steel brackets for Low-Profile Plus CPU Cooler
• 1 x M2.5 screwdriver
• 1 x klucz imbusowy M2
• 1 x Bottom case of armor case
• 2 x Thermal Pads
• 1 x Additional heat sink (for PCB)

3. Konfiguracja i instalacja

Follow these steps to install the Low-Profile Plus CPU Cooler on your Raspberry Pi 5:

1. Prepare Thermal Pads: Locate the two thermal pads and the additional heat sink for the PCB. Carefully peel off the protective film from both sides of the thermal pads.
2. Załóż podkładki termiczne: Place the thermal pads onto the designated areas of your Raspberry Pi 5's PCB, as indicated in Figure 3. Ensure good contact with the components requiring cooling.
3. Mount Cooler: Position the Low-Profile Plus CPU Cooler over the Raspberry Pi 5 CPU, aligning the mounting holes. Secure the cooler using the provided M2.5*6+4mm hand-tightened copper nuts and M2.5*6mm screws. Use the steel brackets if necessary for additional stability.
4. Podłącz wentylator: Connect the fan's power cable to the appropriate fan interface on the Raspberry Pi 5. Ensure the yellow wire is positioned outside, as shown in Figure 4.
5. Install Bottom Case (Optional): If using the included bottom case of the armor case, attach it to the Raspberry Pi 5 assembly using the M2.5*10mm Hexagon screws.

Figure 3: Cooler dimensions and thermal pad placement on Raspberry Pi 5 PCB.

Figure 4: Fan interface connection and copper heat pipe detail.

4. Instrukcja obsługi

The fan on the Low-Profile Plus CPU Cooler is controlled by the Raspberry Pi OS's Linux kernel. It is designed to activate automatically when the CPU temperature reaches 60°C (140°F). Manual control of the fan speed is not supported by this hardware configuration.

Rysunek 5: Example CPU Temperature Bench Test results over 30 minutes.

5. Konserwacja

To ensure optimal performance and longevity of your CPU cooler, periodic maintenance is recommended:

• Usuwanie kurzu: Gently clean the fan blades and aluminum fins with a soft brush or compressed air every few months to prevent dust buildup, which can impede airflow and cooling efficiency.
• Kontrola: Periodically check the fan for any signs of wear or damage. Ensure all mounting screws remain tight.

6. Rozwiązywanie Problemów

Wentylator nie kręci się:

If the fan does not spin, please note the following:

• The fan is controlled by the Raspberry Pi OS's Linux kernel. It will only activate when the CPU temperature reaches 60°C. This is normal operation and not a malfunction.
• Ensure the fan cable is securely connected to the Raspberry Pi 5's fan interface.
• Verify that your Raspberry Pi OS is up to date, as fan control is managed by the operating system.

7. Specyfikacje

8. Wskazówki użytkownika

• Thermal Interface Material: The package includes thermal pads for heat transfer. Ensure you remove the protective film from both sides of the thermal pads before installation for effective cooling.
• Działanie wentylatora: Do not be alarmed if the fan is not spinning immediately after powering on your Raspberry Pi. It is designed to activate only when the CPU temperature reaches 60°C, as managed by the Raspberry Pi OS.

9. Wsparcie techniczne

For additional technical information, detailed guides, or troubleshooting assistance, please refer to the official 52Pi Wiki page for this product:

EP-0226 - 52Pi Wiki