FeiyuTech SCORP 2 3-Axis Handheld Gimbal Stabilizer User Manual

1. Koniecview

The FeiyuTech SCORP 2 is a versatile 3-axis handheld gimbal stabilizer designed for mirrorless and DSLR cameras. It features a built-in AI tracking module, a 1.3-inch touchscreen, and an integrated handle for enhanced control and comfort. The quick-release design allows for instant vertical filming setup without additional accessories.

2. Rozpoczęcie pracy

2.1 Ładowanie

Before initial use, fully charge the gimbal battery. Use the provided USB-C cable for charging. The gimbal supports quick charging with power up to 18W.

2.2 Adjust the Gimbal to Balancing Position

The gimbal is folded by default. Unlock all three axes and adjust the gimbal to its balancing position, then lock the axes. This prepares the gimbal for camera mounting and balancing.

2.3 Using Support Stand

The gimbal can be placed on a flat surface using its built-in kickstand or by attaching the included tripod.

3. Montaż kamery

Before mounting your camera, ensure it is ready for shooting: lens installed, lens cover removed, memory card and battery inserted, and battery fully charged. The gimbal should be powered off or in sleep mode and adjusted to the balancing position.

3.1 Attach the Quick Release Plate and Camera Backing Base (Optional)

Attach the quick release plate to your camera by tightening the screw. For long or heavy lenses, attach the camera backing base to the camera, then secure it to the quick release plate with two screws.

3.2 Instalacja uchwytu soczewki (opcjonalnie)

If needed, install the lens holder on the quick release plate, ensuring the rubber part is directly under the lens. This is recommended for long or heavy lenses.

3.3 Zamontuj kamerę na gimbalu

Unlock the gimbal, slide the camera assembly into the slot, then lock it. Loosen the appropriate adjustment, slide the camera assembly as indicated, and adjust the camera forward and backward until it is roughly balanced. Finally, tighten the adjustment.

4. Równoważenie gimbala

Proper balancing is crucial for optimal performance. Ensure the camera and lens are ready, and the gimbal is off or in sleep mode. It is recommended to hold the camera up while adjusting the slide arm, cross arm, and vertical arm.

4.1 Balancing the Tilt Axis

Unlock the tilt lock and loosen the slide arm lock. Rotate the tilt axis so the camera lens points upward. If the lens tilts to one side, move the slide arm in the opposite direction until the camera is steady. Tighten the slide arm lock while holding the camera. For depth adjustment, rotate the tilt axis so the lens points forward. If it tilts, unlock the quick release plate and move it in the opposite direction until steady. Lock the quick release plate. The tilt axis is balanced when the camera remains steady when tilted up or down by 45 degrees.

4.2 Balancing the Roll Axis

Unlock the roll lock. If the camera tilts to one side, loosen the cross arm lock knob and move the cross arm in the opposite direction until the camera is horizontal and steady. Tighten the cross arm lock knob. The roll axis is balanced when the camera stays still and horizontal.

4.3 Balancing the Pan Axis

Unlock the pan lock. Hold the tripod and tilt the gimbal forward until it is horizontal. If the camera tilts, loosen the vertical arm lock knob and move the vertical arm in the opposite direction until the camera is horizontal and steady. Tighten the vertical arm lock knob. The pan axis is balanced when the camera stays still and horizontal.

4.4 Using the Memory Slider

The Feiyu SCORP 2 includes a memory slider to simplify re-balancing. After balancing, move the memory slider to a hole in the axis so the red dot is exposed. This marks the current position. For future setups with the same equipment, simply align the red dot to quickly achieve balance.

5. Power ON/OFF & Wake Up

5.1 Włączanie/wyłączanie zasilania

Before powering on, ensure the gimbal is balanced and all three axes are unlocked. If axes are locked, the gimbal will enter sleep mode for protection. Long press the power button until you hear a beep to power on/off. For first-time use or after changing cameras/lenses, set motor power (refer to section 8.3.1).

5.2 Lock/Unlock Screen

Single tap the F2 button to lock the screen. Single tap F2 again to unlock.

5.3 Sleep/Wake Up

Double tap the power button to enter sleep mode. To wake up, single tap the power button or tap the 'Z' icon on the screen.

6. Wprowadzenie do funkcji/trybów

6.1 Follow Modes

• PF (Pan Follow): Only the pan axis follows your hand movement.
• PTF (Pan and Tilt Follow): Both pan and tilt axes follow your hand movement; roll axis does not.
• FPV (widok z pierwszej osoby) View): All three axes (pan, tilt, roll) follow your hand movement.
• Zamek: All three axes are fixed, maintaining the camera's direction.
• FFW (Flash Follow): All three axes follow your hand movement at high speed.

6.2 Inne funkcje

• Automatyczne obracanie: Achieve image rotating scenes by setting rotation speed and direction.
• Tryb portretowy: Enter portrait mode for vertical video recording or live streaming.
• Tryb selfie: Camera turns 180° horizontally for selfie shooting.
• Track Video: Record video along preset waypoints.
• Blokada ręczna: Manually move the camera to a desired position and hold for half a second to save new tilt/pan positions.

7. Łączenie aplikacji

7.1 Połącz się z aplikacją Feiyu SCORP

To connect, turn on the gimbal and enable Bluetooth on your smartphone. Open the Feiyu SCORP App and tap the top of the home page to connect. Once connected, you can control the gimbal via the app, including virtual joystick control, mode switching, motor power/camera parameter adjustments, follow speed settings, and firmware updates.

7.2 Function Introduction of App

The Feiyu SCORP App provides extensive control and customization:

• Gimbal Control Access: Displays product name and battery level. Tap to access virtual joystick, switch follow modes, recenter gimbal, and adjust horizontal angle.
• Odłącz urządzenie: Tap to disconnect the current device.
• Scenariusze: Access auto rotation, panorama, timelapse (Motionlapse/Static timelapse/Hyperlapse), and track video.
• Ustawienia przycisków: Customize trigger button functions, set auto focus time, and attitude change time for A/B buttons.
• Ustawienia pokrętła: Set the multifunction knob's control object (axes, electronic focus, focus motor), and adjust damp, speed, smooth, and sound.
• Motor Power Settings: Manually adjust motor power for tilt, roll, and pan axes, or use auto tune.
• Śledź prędkość: Select preset profiles (Slow/Med/Fast) or customize follow speed and dead zone.
• Ustawienia aparatu: Adjust camera aperture, shutter speed, and ISO parameters when connected.
• Horizon Calibration: Calibrate the gimbal automatically or manually.
• Więcej: Set boot silent, disable selfie, manual lock, check firmware info, update firmware, and restore default settings.
• Z powrotem: Wróć do strony głównej.
• Connect with Image Transmission Device: Connect to an image transmission device.
• Joystick Settings: Adjust joystick speed for pan/tilt axis control and invert joystick direction.
• Centrum: Stuknij, aby wycentrować gimbal.
• Flash Follow (FFW): Tap to enter Flash Follow mode.
• Tryb portretowy: Stuknij, aby przejść do trybu portretowego.
• Tryb selfie: Stuknij, aby przejść do trybu selfie.
• Adjust Horizontal Angle: Slide to control roll axis and adjust horizontal angle.
• Wirtualny joystick: Use the virtual joystick to control pan and tilt axes.
• Tryb blokady: Stuknij, aby przejść do trybu blokady.
• Migawka: Take photos or start/stop video recording.
• Switch between Photo/Video Mode: Przełączaj się między trybem zdjęć i wideo.
• Śledzenie panoramiczne (PF): Tap to enter Pan Follow mode.
• Pan and Tilt Follow (PTF): Tap to enter Pan and Tilt Follow mode.
• FPV: Stuknij, aby przejść do trybu FPV.
• Motion Sensing Mode: Control pan and tilt axes by moving your smartphone.

8. Działanie

8.1 przycisk obsługi

• Przycisk zasilania: Long press for ON/OFF. Single tap for wake up (sleep mode) or battery level. Double tap to enter sleep mode.
• Przycisk trybu: Single tap to cycle through PF/PTF/FPV. Tap five times for Horizon calibration.
• Przycisk spustowy: Double tap to recenter. Triple tap to enter/exit selfie mode. Press and hold for PTF (release to exit). Customizable via app.
• Drążek sterowy: Controls tilt and pan axes movement.
• Spust migawki: Half press for focus. Single tap (fully) to start/stop recording. Long press (fully) to take photo.
• FPV Button: Single tap to enter/exit FPV mode.
• Przycisk F1: Double tap to enter/exit portrait mode. Triple tap for AI power ON/OFF. Long press to enter/exit AI Tracking (when AI power is enabled).
• F2 Button (Home Button): Single tap to lock/unlock screen (home page) or return to home page (other pages). Double tap to enter FFW mode. Long press for motor power auto tuning.
• Przycisk A/B: Long press to mark current position as A/B. Single tap to return to marked A/B position.
• Knob Function Switching Button: Single tap to switch control object (3 axes movement, electronic focus/zoom). Long press to cycle through multifunction knob control options.
• Gałka wielofunkcyjna: Turn to control roll, tilt, pan axes; focus/zoom; focus motor; or adjust parameters on the touchscreen.
• Kluczowe kombinacje: Long press F1 + F2 buttons to clear Bluetooth connections.

8.2 Obsługa ekranu dotykowego

The 1.3-inch touchscreen provides intuitive control and information:

• Current Battery Level: Displays gimbal battery status.
• Podłączenie aparatu: Icon appears when camera is successfully connected.
• Połączenie Bluetooth: Icon appears when Bluetooth is connected.
• Moc silnika: Use auto tune or manually adjust motor power for each axis.
• Śledź prędkość: Select preset or custom follow speed profiles.
• Tryb śledzenia: Select desired gimbal follow mode.
• Scenariusz: Choose shooting scenarios like timelapse, auto rotation, panorama, portrait mode, selfie mode, track video.
• Joystick Settings: Adjust joystick speed and direction.
• Ustawienia gimbala: Disable selfie, manual lock, horizon calibration.
• Ustawienia Bluetooth: Connect to camera or smartphone via Bluetooth.
• Ustawienia podświetlenia: Dostosowanie jasności ekranu.
• Śledzenie AI: Triple tap F1 or toggle via More Settings to turn AI power ON/OFF. Use gestures (spread palm for shutter, OK gesture for start/stop tracking, thumbs opposite direction for stop tracking, double L-shaped for custom framing).

8.3 Control Ports

The gimbal features a camera control port, an image transmission port, and two extension ports on the fixed plate for connecting accessories like a focus motor.

9. Wskazówki użytkownika

• Kompatybilność aparatu: Always check the official FeiyuTech website for the latest camera and lens compatibility list to ensure optimal performance.
• Motor Power Adjustment: If the gimbal vibrates at high frequency, the motor power might be too strong. If it shakes with low frequency and large amplitude, the motor power might be too weak. Adjust accordingly in the settings.
• Połączenie Bluetooth: Ensure your camera's Bluetooth function is enabled when attempting to connect the gimbal via Bluetooth for camera control.

10. Specyfikacje

11. Akcesoria

The FeiyuTech SCORP 2 package includes the following items:

• USB 2.0 to USB-C Charging Cable x1
• Kabel sterujący USB-C do mikrokamery x1
• Kabel sterujący kamerą USB-C do USB-C x1
• Kabel sterowania kamerą USB-C do TRS2.5 x1
• Kabel USB-C do sterowania wieloma kamerami x1
• Kabel sterowania kamerą USB-C do 2.5 mm (DC 2.5 mm) x1
• Kabel sterowania kamerą USB-C do TRS3.5 x1
• Kabel USB-C do sterowania kamerą Mini x1
• Statyw x1
• Stała płyta x1
• Suwak x1
• Płyta szybkiego uwalniania x1
• Camera backing base x1
• Uchwyt obiektywu x1
• Śruba uchwytu obiektywu x1
• Śruba mocująca kamerę x3

12. Przechowywanie i konserwacja

• Przechowywać produkt w miejscu niedostępnym dla dzieci i zwierząt domowych.
• Do not leave the product near heat sources (furnace, heater) or inside a vehicle on hot days.
• Przechowuj produkt w suchym miejscu.
• Do not overcharge or overuse the battery; charge it at least once a month if not used for a long time.
• Nigdy nie używaj produktu, jeżeli temperatura jest zbyt wysoka lub zbyt niska.

13. Ostrzeżenia dotyczące bezpieczeństwa

Ogólne ostrzeżenia dotyczące użytkowania

• Ensure motor spinning is not blocked by external force when powered on.
• Do not contact water or other liquids unless the product is marked waterproof/splash-proof. Avoid sea water or corrosive liquids.
• Do not disassemble the product except for marked detachable parts. If accidental disassembly occurs, contact FeiyuTech after-sales or an authorized service center for repair.
• Prolonged operation may cause the product surface temperature to rise; operate carefully.
• Do not drop or strike the product. Contact after-sales support if the product is abnormal.

Oświadczenie o narażeniu na promieniowanie IC

Sprzęt ten jest zgodny z limitami ekspozycji na promieniowanie IC obowiązującymi w środowisku niekontrolowanym.

Zgodność z przepisami FCC

To urządzenie jest zgodne z częścią 15 przepisów FCC. Jego działanie podlega następującym dwóm warunkom: (1) To urządzenie nie może powodować szkodliwych zakłóceń i (2) to urządzenie musi akceptować wszelkie odbierane zakłócenia, w tym zakłócenia, które mogą powodować niepożądane działanie.

Notatka: This equipment has been tested and found to comply with the limits for a Class B digital device. If interference occurs, try reorienting the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a radio/TV technician. Unauthorized modifications could void the user's authority to operate the equipment.

14. Gwarancja i pomoc techniczna

For detailed support, please contact FeiyuTech:

• Producent: Firma Guilin Feiyu Technology Incorporated
• Webstrona: www.feiyu-tech.com
• E-mail: support@feiyu-tech.com
• Telefon: +86 773-2320865

For a detailed user manual (PDF), please refer to the official document available at https://manuals.plus/m/e1a03aea816a350a697ab8d6ecd85eb15a6c3e2c27164c8620e81c23f51af6e9.