Favoto Smart Bike Helmet ZL-FSM-01 Instruction Manual

1. Koniec produktuview

The Favoto Smart Bike Helmet (Model ZL-FSM-01) is designed for road cycling and city commuting, featuring integrated lighting and turn signals for enhanced visibility. This helmet is CPSC certified, ensuring compliance with safety standards.

Figure 1: Favoto Smart Bike Helmet with remote control and rear view.

Figure 2: Dual-shell design for enhanced safety and durability.

2. Zawartość opakowania

Sprawdź, czy w opakowaniu znajdują się wszystkie elementy:

• Inteligentny kask
• Zdalne sterowanie
• Kabel do ładowania USB typu C.
• Instrukcja obsługi

Figure 3: Included components: Smart Helmet, Remote Control, USB Type-C Cable, and Manual.

3. Instalacja i montaż

3.1. Regulacja kasku

Ensure the helmet fits securely and comfortably. The helmet features an adjustable dial at the rear to customize the fit for head circumferences between 57-61 cm (22.4-24 inches).

1. Załóż kask na głowę, upewniając się, że leży równo i zakrywa czoło.
2. Turn the adjustable dial clockwise to tighten the fit until snug, but not uncomfortably tight.
3. Turn the dial counter-clockwise to loosen the fit.

Figure 4: Proper helmet fitting using the adjustable dial.

3.2. Magnetic Buckle

The helmet is equipped with a magnetic buckle for quick and secure fastening. To fasten, bring the two buckle parts close together; they will snap into place magnetically. To release, slide the buckle parts apart.

Figure 5: Magnetic buckle for secure and effortless fastening.

3.3. Ładowanie kasku

The helmet's integrated lights are powered by a rechargeable battery. Use the provided USB Type-C cable to charge the helmet. The charging port is located at the bottom rear of the helmet, beneath a weather-proof cover.

Figure 6: Charging features of the helmet.

4. Instrukcja obsługi

4.1. Powering On/Off and Tail Light Modes

To power on the helmet's tail lights, press and hold the power button located at the rear of the helmet for 3 seconds. Short presses will cycle through the five available tail light modes:

• Stały czerwony
• Powolny błysk czerwony
• Oddychający czerwony
• Szybki błysk czerwony
• Double Flash Yellow (Hazard)

The helmet will remember the last selected mode when powered off and on again.

Figure 7: Five dynamic lighting modes for visibility.

4.2. Remote Control for Turn Signals

The included remote control allows for easy activation of turn signals and cycling through tail light modes while riding. Mount the remote control on your bicycle's handlebars for convenient access.

• Naciśnij "L" button for a left turn signal.
• Naciśnij "R" button for a right turn signal.
• Naciśnij "M" button to cycle through the tail light modes.

Activating a turn signal will temporarily override the current tail light mode. The turn signal will flash for a set duration before returning to the previous tail light mode.

Figure 8: Remote control for turn signals and mode selection.

5. Konserwacja

5.1. Czyszczenie

• Wyczyść skorupę kasku miękką,amp szmatką i delikatnym mydłem. Unikaj silnych środków chemicznych i ściernych środków czyszczących.
• The inner padding can be removed and hand-washed with mild soap and water, then air-dried.

5.2. Przechowywanie

Store the helmet in a cool, dry place away from direct sunlight and extreme temperatures. Do not store the helmet near heat sources or corrosive materials.

5.3. Pielęgnacja baterii

To prolong battery life, charge the helmet regularly, even if not in frequent use. Avoid fully discharging the battery for extended periods.

6. Rozwiązywanie Problemów

This section addresses common issues you might encounter with your Favoto Smart Bike Helmet.

6.1. Światła się nie włączają

• Ensure the helmet battery is charged. Connect the helmet to the USB Type-C charging cable and allow sufficient time for charging.
• Press and hold the power button on the helmet for 3 seconds to activate the lights.

6.2. Pilot zdalnego sterowania nie odpowiada

• Ensure the helmet lights are powered on.
• Sprawdź baterię w pilocie. W razie potrzeby wymień ją.
• To re-pair the remote control with the helmet:
  1. Turn on the helmet lights by holding the switch for 3 seconds.
  2. When the lights flash alternately (red and yellow), press any button on the remote control.
  3. A steady flash on the helmet indicates successful pairing.

6.3. Difficulty Accessing Charging Port

The charging port is located under a small, weather-proof rubber flap at the bottom rear of the helmet. Gently lift this flap to expose the Type-C port for charging.

7. Specyfikacje

8. Gwarancja i wsparcie

For warranty information, product support, or to contact customer service, please refer to the official Favoto website or your purchase documentation. You can also visit the Favoto Store on Amazon.