Produkt ponadview
This document provides instructions for the replacement remote control compatible with specific Okin adjustable bed base models, including JLDK.30.03.13 RF368B. This remote is designed to operate the various functions of your adjustable bed base. It is crucial to ensure your control box and existing remote are identical to the compatible models before use.
Please note that batteries are not included with this remote control. Refer to the specifications section for battery requirements.
Konfiguracja i początkowe parowanie
1. Instalacja baterii
The remote control requires 2 AAA batteries. To install:
- Znajdź pokrywę komory baterii z tyłu pilota.
- Aby otworzyć komorę, przesuń lub odepnij pokrywę.
- Włóż 2 baterie AAA, upewniając się, że bieguny dodatni (+) i ujemny (-) są prawidłowo ustawione względem oznaczeń wewnątrz komory.
- Dokładnie załóż pokrywę komory baterii.
2. Parowanie pilota
Follow these steps to pair the remote control with your adjustable bed base. This process typically needs to be completed within a short timeframe after power cycling the bed base.
- Krok 1: Unplug the power cord of your adjustable bed base from the electrical outlet.
- Krok 2: Wait approximately 5 seconds, then plug the power cord back into the outlet.
- Krok 3: Within 10 seconds of plugging the power cord back in, locate the PAIR button on the back of the remote control.
- Krok 4: Press and hold the PAIR button. The PAIR button will illuminate blue and begin flashing.
- Krok 5: Continue holding the PAIR button until it stops flashing and the LED light on the control box of your bed base goes out.
- Krok 6: Release the PAIR button. The remote control is now paired with the adjustable base.
- Krok 7: Test all remote functions to confirm successful pairing.
Image: The black replacement remote control for Okin adjustable bed bases. It features a glossy finish with clearly marked buttons for head and foot adjustments, a flat button for returning to a flat position, and a "ZERO G" button for the zero gravity preset. There are also two circular buttons, one with a single line and another with two lines, likely for memory presets or pause/play functions.
Instrukcja obsługi
Once paired, the remote control allows you to operate the various functions of your adjustable bed base. The buttons are typically intuitive and correspond to specific movements or presets.
- Głowa w górę/w dół: Buttons with wavy lines or arrows typically control the head section of the bed.
- Podnoszenie/opuszczanie stopy: Buttons with wavy lines or arrows typically control the foot section of the bed.
- Pozycja płaska: A button with a single horizontal line usually returns the bed to a completely flat position.
- ZERO G: The "ZERO G" button activates the pre-programmed zero gravity position, which elevates the head and foot to a specific angle designed to relieve pressure.
- Ustawienia pamięci: Other buttons (e.g., with single or double lines) may be for custom memory positions. Refer to your bed base's original manual for specific functions of these buttons.
Press and hold the desired button to move the bed section. Release the button to stop movement.
Konserwacja
Czyszczenie pilota
Do czyszczenia pilota należy używać miękkiej, suchej ściereczki. W przypadku uporczywych zabrudzeń należy użyć delikatnej ściereczki.amp cloth with mild soap can be used, but ensure no moisture enters the remote. Do not use abrasive cleaners or solvents.
Wymiana baterii
Replace batteries when the remote's response becomes sluggish or if the indicator light (if present) does not illuminate. Follow the battery installation steps outlined in the "Setup and Initial Pairing" section.
Rozwiązywanie problemów
If your remote control is not functioning as expected, consider the following troubleshooting steps:
- Sprawdź baterie: Ensure batteries are correctly installed and have sufficient charge. Replace them if necessary.
- Ponowne parowanie: If the remote loses connection, attempt the pairing process again as described in the "Setup and Initial Pairing" section.
- Control Box Verification: Przed zakupemasing this replacement remote, it is essential to troubleshoot your bed's control box. Verify that the old remote control's product number (often found in the battery compartment) matches the compatible models for this replacement. This remote only fits specific control boxes and models.
- Power Cycle Bed Base: Unplug the bed base from the wall outlet for 30 seconds, then plug it back in. This can reset the system.
- Przeszkody: Ensure there are no obstructions preventing the remote's signal from reaching the bed base's receiver.
If issues persist after following these steps, further assistance may be required.
Specyfikacje
| Model | JLDK.30.03.13 RF368B (Serial-No.: 6800120015A18B161766) |
| Marka | Ogólny |
| Kompatybilne urządzenia | Adjustable bed base (specific Okin models) |
| Wymagane baterie | 2 x AAA (brak w zestawie) |
| Kolor | Czarny |
| Funkcja specjalna | Not a Universal remote |
Wsparcie
For further assistance or if you are unsure about compatibility, please provide detailed information about your bed base, control box, old remote control, and any available manual to the seller. This will help in verifying the correct item or providing specific troubleshooting guidance.
It is recommended to refer to the original manual for your adjustable bed base for comprehensive instructions on its features and pairing procedures.
