Wstęp
This manual provides detailed instructions for the installation, operation, and programming of the GODIYMODULES DC 6-30V Timer Switch LED Digital Time Delay Relay Module, Model XYWJ01-001. Please read this manual thoroughly before use to ensure proper functionality and safety.
Rycina 1: Przód view of the DC 6-30V Timer Switch LED Digital Time Delay Relay Module.
Informacje dotyczące bezpieczeństwa
Zawsze przestrzegaj następujących środków ostrożności:
- Upewnij się, że napięcie zasilaniatage mieści się w określonym zakresie od 6 V do 30 V prądu stałego.
- Disconnect power before making any wiring connections or adjustments.
- Unikaj wystawiania modułu na działanie wilgoci, ekstremalnych temperatur i środowiska korozyjnego.
- Do not attempt to disassemble or modify the module beyond the instructions provided.
- Jeśli nie masz pewności co do instalacji elektrycznej, instalację powinien wykonać wykwalifikowany personel.
Konfiguracja i okablowanie
The module requires a DC power supply between 6V and 30V. It features a terminal block for power input and relay output connections.
Połączenia końcowe
Rysunek 2: Tył view showing the terminal block for power and relay connections.
The terminal block typically includes connections for:
- V+: Positive power input (DC 6-30V)
- V-:Ujemne wejście zasilania (masa)
- L1: Relay Normally Open (NO) contact
- L2: Relay Common (COM) contact
- L3: Relay Normally Closed (NC) contact (if applicable, check module markings)
Refer to the markings on your specific module for exact terminal identification.
DC 6.0~30V Wiring Mode
Figure 3: Wiring diagram for connecting the module to a DC 6-30V power supply and a DC load.
For DC loads, connect the positive terminal of your DC power supply to V+ and the negative terminal to V-. The load should be connected in series with the relay's common (COM) and normally open (NO) contacts, or normally closed (NC) depending on desired operation.
220V Wiring Mode (AC Load)
Figure 4: Wiring diagram for connecting the module to a DC 6-30V power supply and an AC 220V load.
OSTRZEŻENIE: When connecting AC loads, extreme caution must be exercised. Ensure all power is disconnected before wiring. AC wiring should only be performed by individuals with appropriate electrical knowledge and safety training.
For AC loads, the module itself is powered by DC 6-30V. The relay contacts then switch the AC 220V circuit. Connect the AC 220V live (fire) line to the relay's common (COM) contact, and the normally open (NO) contact to one side of your AC load. The other side of the AC load connects to the AC neutral (zero) line.
Trigger Input and Serial Communication
Figure 5: Trigger input connections, relay output, and location of UART port.
The module supports high and low-level trigger inputs. Connect your trigger signal to the designated trigger input pin (refer to module markings or the diagram above). The signal ground (GND) should be common with the module's power ground.
For UART communication, the port is located behind the back cover. Carefully remove the back cover to access the UART pins. The default UART settings are 9600 baud, 8 data bits, 1 stop bit (9600,8,1).
UART Commands:
- Czytać: Read system parameters
- OP:xxxx: Set ON time (e.g., OP:1s, OP:0.1s, OP:0.01s, OP:1min)
- CL:xxxx: Set OFF time (e.g., CL:1s, CL:0.1s, CL:0.01s, CL:1min)
- LP:xxxx: Set loop cycles
- start: Trigger/Start (P0-P7 Active)
- zatrzymywać się: Pause (P0-P7 Active)
- PX: Set the working mode (P0-P9)
Instrukcja obsługi
The module features an LCD display and several buttons for operation and programming.
Button Functions and Display
Figure 6: Front panel with labeled buttons and display elements.
- Setting Button (Gear icon): Used to enter and navigate programming modes.
- Add Button (Up arrow): Increases parameter values.
- Reduce Button (Down arrow): Decreases parameter values.
- Pause/Trigger Button (Power icon): Pauses/resumes timing or acts as a manual trigger.
- Wyświetlacz LCD: Shows current working mode (e.g., P0.0P), timing status, and time values. "OUT" indicates the relay is closed.
Programming Modes (P0-P9)
The module supports various operating modes, typically designated as P0.0 to P9.9. To enter programming mode, press and hold the Przycisk ustawień. Użyj Dodać I Zmniejszyć buttons to select the desired mode. Press the Przycisk ustawień again to confirm and enter parameter settings for that mode. Use Dodać I Zmniejszyć to adjust values (OP, CL, LP) and the Pause/Trigger Button to switch between time units (seconds, minutes, hours).
Common Modes (Example):
- P0.0: Timer ON (OP) then OFF (CL) once.
- P1.0: Timer ON (OP) then OFF (CL) in a loop (LP cycles).
- P2.0: Trigger ON (OP) then OFF (CL) once.
- P3.0: Trigger ON (OP) then OFF (CL) in a loop (LP cycles).
- (Specific mode details may vary; refer to the module's on-screen prompts or detailed documentation for your exact firmware version.)
After setting parameters, press and hold the Przycisk ustawień aby zapisać i wyjść z trybu programowania.
Stan małej mocy
If no operation is performed for 5 minutes, the module will enter a low-power state. Any button press will wake it up.
Konserwacja
The GODIYMODULES Timer Switch is designed for low maintenance. To ensure optimal performance:
- Utrzymuj moduł w czystości, bez kurzu i zanieczyszczeń. Do czyszczenia używaj miękkiej, suchej ściereczki.
- Okresowo sprawdzaj połączenia przewodów, aby mieć pewność, że są bezpieczne.
- Avoid exposing the module to direct sunlight or excessive heat, which can degrade electronic components.
Rozwiązywanie problemów
If you encounter issues with your timer module, refer to the following common problems and solutions:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Moduł nie włącza się. | Niewłaściwe napięcie zasilaniatage or polarity; loose wiring. | Verify power supply is 6-30V DC and connected correctly (V+ to positive, V- to negative). Check all wiring connections. |
| Przekaźnik nie aktywuje się. | Incorrect programming mode; load wiring issue; trigger not detected. | Check the selected programming mode and parameters (OP, CL). Ensure the load is correctly wired to the relay contacts. If using a trigger, verify the trigger signal is correct and connected properly. |
| Display shows unexpected characters or behavior. | Power fluctuations; internal error. | Disconnect power for a few seconds, then reconnect. If the issue persists, contact support. |
| Difficulty programming the module. | Unfamiliarity with button sequence or mode logic. | Carefully re-read the "Operating Instructions" section, especially "Programming Modes." Practice the button sequences. Consider using UART for programming if comfortable. |
Specyfikacje
- Model: XYWJ01-001
- Zasilanie: DC 6V ~ 30V
- Wyświetlacz: LCD with two columns
- Tryb wyzwalania: High level, Low level, Switch quantity
- UART Communication: Tak (9600,8,1)
- Low-Power Mode: Automatic entry after 5 minutes of inactivity
- Wymiary produktu: 2.24 x 1.17 x 0.8 cala (56.9 x 29.7 x 20.3 mm)
- Waga przedmiotu: 1.76 uncji (50 grama)
- Producent: GODIYMODULES
Gwarancja i wsparcie
For warranty information or technical support, please contact your retailer or the manufacturer, GODIYMODULES. Keep your purchase receipt as proof of purchase.
Manufacturer: GODIYMODULES
Model: XYWJ01-001