BOSYTRO SJK-24V-480W-WX 24V 20A 480W DC Switching Power Supply User Manual

1. Wprowadzenie

This manual provides essential instructions for the safe and efficient operation of your BOSYTRO SJK-24V-480W-WX 24V 20A 480W DC Switching Power Supply. This unit is designed to convert AC mains power to a stable DC 24V output, suitable for a wide range of applications including LED strips, 3D printers, and CCTV camera security systems. Please read this manual thoroughly before installation and use, and retain it for future reference.

Obraz 1.1: The BOSYTRO 24V switching power supply is suitable for various applications such as LED advertising displays, security monitoring systems, automation equipment, car audio, LED light strips, and medical equipment.

2. Instrukcje bezpieczeństwa

Aby zapewnić bezpieczną obsługę i zapobiec uszkodzeniom, należy przestrzegać następujących środków ostrożności:

• Wejście VoltagWybór: Before connecting the power supply, verify that the input voltage switch (115V/230V) is set to match your local mains voltagmi. Nieprawidłowa objętośćtagWybór ten może spowodować uszkodzenie urządzenia.
• Prawidłowe okablowanie: Ensure all wiring connections are secure and correct. Pay close attention to positive (V+) and negative (V-) DC output terminals and AC input connections (Live, Neutral, Ground).
• Grunt: Always connect the ground terminal to a proper earth ground to prevent electrical shock.
• Zabezpieczenie przed przeciążeniem: Do not exceed the maximum output current of 20A or power of 480W. Overloading can trigger protection mechanisms or damage the unit. For equipment with high peak variations (e.g., motors), select a power supply with at least 2 times the rated power.
• Wentylacja: Ensure adequate ventilation around the power supply. Do not block the cooling fan or ventilation holes. Maintain the operating temperature range of 14℉-140℉ (-10℃-60℃).
• Warunki środowiskowe: Unikaj wystawiania urządzenia na działanie wilgoci, kurzu i ekstremalnych temperatur.
• Profesjonalna instalacja: Installation and wiring should be performed by qualified personnel to prevent electrical hazards.
• Brak części nadających się do samodzielnej naprawy przez użytkownika: Nie otwierać zasilacza casing. There are no user-serviceable parts inside, and opening it voids the warranty.

Obraz 2.1: The power supply features multiple protections including short circuit, over-voltage, overload, earth leakage, overcurrent, and overheat protection. Note: The power cord is for reference wiring use only and is not included.

3. Koniec produktuview

3.1 Główne cechy

• AC/DC 24V Power Supply: Provides a default DC 24V output with an adjustable range of ±10% (21.6V-26.4V).
• Wysoka moc wyjściowa: Delivers up to 20A and 480W of maximum power with an efficiency of up to 80%.
• Upgraded Output Ports: Features three output channels and an added power port for easier and faster connections, eliminating the need for separate Fire, Ground, and Zero cables.
• Efektywne odprowadzanie ciepła: Constructed with a porous metal aluminum shell and equipped with a built-in cooling fan for stable and low-noise heat management.
• Wielorakie zabezpieczenia: Incorporates smart chip technology for overload, over-voltage, overheat, and short circuit protection. Certified with RoHS/CE/LVD/EMC standards.
• Wejście Voltage Przełącznik: Możliwość wyboru głośności wejściowejtage between 115V and 230V to accommodate different regional power standards.

3.2 Składniki

The BOSYTRO SJK-24V-480W-WX power supply is composed of high-quality electronic components housed within a durable aluminum casing.

Obraz 3.1: Szczegółowy view of the power supply's internal structure, showing the high-quality PCB circuit board, aluminum housing, fan cooling device, built-in filter jammer, and other electronic components.

Obraz 3.2: Koszty ogólne view of the BOSYTRO SJK-24V-480W-WX power supply, highlighting its physical dimensions (21.5cm x 11.5cm x 5cm) and a table of key specifications.

4. Instrukcje konfiguracji

4.1 Select Input Voltage

Before connecting the power supply to an AC source, it is critical to set the input voltage switch to match your local power grid. The switch is located on the side of the unit. For American and Canadian customers, set it to 115V. For European customers, set it to 230V. Failure to select the correct voltage can result in damage to the power supply and connected equipment.

Obraz 4.1: Wejście voltage selector switch, showing options for 115V (USA/CA) and 230V (EU). Ensure this is correctly set before powering on.

4.2 Power Supply Check (Initial Test)

After setting the input voltage, perform a quick check:

1. Ensure the power supply is not connected to any load devices.
2. Plug a power cord (not included) into the AC input port of the power supply.
3. Turn on the power switch. Observe the indicator lights. If both the red and green lights are on, the power supply is functioning normally.
4. Turn off the switch and unplug the power cord before proceeding to connect your devices.

4.3 Podłączanie urządzenia

Connect your load device(s) to the DC output terminals. The power supply features three positive (V+) terminals and three negative (V-) terminals for connecting multiple devices. Ensure correct polarity to prevent damage to your devices.

• Connect the positive wire from your device to any V+ terminal.
• Connect the negative wire from your device to any V- terminal.
• Sprawdź, czy wszystkie połączenia są dobrze dokręcone i bezpieczne.

Obraz 4.2: A diagram illustrating the wiring terminals of the 24V power supply, including the AC input, power switch, and DC output terminals (V+ for positive, V- for negative). It also shows the adjustable voltage screw (ADJ) for fine-tuning the output voltage.

5. Instrukcja obsługi

5.1 Włączanie

Once all connections are secure and the input voltage is correctly set, plug the power cord into the AC input and turn on the power switch. The power supply will begin providing 24V DC power to your connected devices.

5.2 Regulacja głośności wyjściowejtage

Objętość wyjściowatage can be fine-tuned within a ±10% range (21.6V-26.4V) using the adjustable voltage screw (labeled 'ADJ') located near the DC output terminals. Use a small screwdriver to carefully turn the screw clockwise to increase voltage lub przeciwnie do ruchu wskazówek zegara, aby zmniejszyć głośnośćtage. Monitoruj objętość wyjściowątage with a multimeter during adjustment to ensure it meets your device's requirements.

6. Konserwacja

Regularna konserwacja pomaga zapewnić długowieczność i niezawodną pracę zasilacza:

• Czyszczenie: Keep the unit clean and free from dust. Use a soft, dry cloth to wipe the exterior. Do not use liquid cleaners or solvents.
• Wentylacja: Periodically check that the ventilation holes and cooling fan are not obstructed. Ensure proper airflow to prevent overheating.
• Znajomości: Regularly inspect all wiring connections for tightness and signs of wear or corrosion. Loose connections can lead to poor performance or safety hazards.
• Składowanie: If storing the unit for an extended period, disconnect it from power, clean it, and store it in a cool, dry place away from direct sunlight and moisture.

7. Rozwiązywanie Problemów

Jeśli masz problemy z zasilaniem, zapoznaj się z poniższymi typowymi procedurami rozwiązywania problemów:

If the problem persists after attempting these solutions, please contact BOSYTRO customer support.

8. Specyfikacje

9. Gwarancja i wsparcie

9.1 Informacje o gwarancji

BOSYTRO provides a warranty for this product. Quality issues can be returned or exchanged. Please retain your proof of purchase for warranty claims.

9.2 Obsługa klienta

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact BOSYTRO customer support through the retailer where the product was purchased or visit the official BOSYTRO webwitryna do informacji kontaktowych.