Produkt ponadview
The InSinkErator Badger 1 is a reliable food waste disposer designed for efficient grinding of everyday food scraps. This model features a 1/3 horsepower motor and a continuous feed design, allowing for uninterrupted use. It comes equipped with a power cord for convenient installation.
Image: The InSinkErator Badger 1 Garbage Disposal unit, shown installed under a kitchen sink with plumbing connections.
Konfiguracja i instalacja
Before beginning installation, ensure the power supply to the existing disposal or wiring is turned off at the circuit breaker. Review all local plumbing and electrical codes.
Zawartość zestawu:
- Disposer unit with pre-attached power cord.
- Mounting assembly (flange, fiber gasket, support ring, mounting ring, screws).
- Stopper/Splash Guard.
- Hex wrench (for clearing jams).
Kroki instalacji:
- Remove Old Disposer (if applicable): Disconnect power, plumbing, and then detach the old disposer from the sink flange.
- Install New Mounting Assembly: Clean the sink opening. Apply plumber's putty around the sink flange and insert it into the sink opening. From below the sink, place the fiber gasket, support ring, and mounting ring onto the flange. Secure with screws, ensuring a tight seal.
- Connect Dishwasher Drain (if applicable): If connecting a dishwasher, a knockout plug must be removed from the disposer's dishwasher inlet. Use a screwdriver and hammer to tap out the plug from the inside of the inlet. Retrieve the plug from inside the disposer. Connect the dishwasher drain hose to this inlet using a hose clamp.
- Attach Disposer to Mounting Assembly: Align the disposer's three mounting tabs with the mounting ring. Twist the disposer until it locks into place. Ensure it is securely seated.
- Connect Drain Plumbing: Connect the disposer's discharge outlet to your household drain system using the provided elbow and gasket. Secure all connections with clampi orzechy.
- Podłączenie elektryczne: The Badger 1 comes with a pre-attached power cord. Plug the power cord into a grounded 120V outlet.
- Test szczelności: Turn on the water and check all connections for leaks. Run the disposer briefly to ensure proper function.
Instrukcja obsługi
The InSinkErator Badger 1 operates with a continuous feed mechanism, allowing you to add food waste while the unit is running.
Podstawowa obsługa:
- Turn on a medium flow of zimno woda.
- Flip the wall switch to turn on the disposer.
- Slowly feed food waste into the disposer opening. Do not overload the unit.
- After grinding is complete, turn off the disposer and let the water run for a few seconds to flush the drain line.
Notatka: This model is designed for effective grinding of common food scraps. While it is not the quietest disposer, its performance is efficient for everyday use.
Konserwacja
Regular maintenance helps ensure the longevity and optimal performance of your disposer.
Czyszczenie:
- To clean the disposer, grind small pieces of citrus peels (lemons, oranges) with cold water. This helps to freshen the unit and clean the grinding chamber.
- Avoid pouring grease or oil down the drain, as this can solidify and cause clogs.
Usuwanie zacięć:
If the disposer hums but does not grind, it may be jammed. Follow these steps:
- Turn off the disposer and the water.
- Insert the provided hex wrench into the center hole on the bottom of the disposer.
- Work the wrench back and forth until the jam is cleared and the motor shaft turns freely.
- Remove the wrench and press the red reset button on the bottom of the disposer.
- Turn on the water and then the disposer to test.
Rozwiązywanie problemów
Przed skontaktowaniem się z pomocą techniczną zapoznaj się z poniższymi problemami i rozwiązaniami.
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Dystrybutor nie uruchamia się | No power; tripped circuit breaker; internal overload. | Check power switch. Reset circuit breaker. Press the red reset button on the bottom of the disposer. |
| Rozdrabniacz brzęczy, ale nie mieli | Zablokowana tarcza szlifierska. | Turn off power. Insert hex wrench into bottom center hole and rotate back and forth to clear jam. Remove wrench and press reset button. |
| Wyciek z młyna | Loose plumbing connections; cracked housing; improper seal. | Check and tighten all plumbing connections. Inspect for cracks. Ensure mounting assembly is properly sealed. |
Specyfikacje
- Model: Borsuk 1
- Silnik: 1/3 koni mechanicznych
- Tomtage: 120 wolty
- Częstotliwość: 60 Hz
- Faza: 1 PH
- Amps: 5.6
Gwarancja i wsparcie
For service or support, please contact InSinkErator directly. The product typically includes a manufacturer's warranty. Refer to the documentation included with your product for specific warranty terms and conditions.
Obsługa klienta: 1-800-558-5700