GODIYMODULES BMS 10S 36V 15A Li-ion Battery Management System

Wstęp

This manual provides essential information for the proper installation, operation, and maintenance of your GODIYMODULES 10S 36V 15A Li-ion Battery Management System (BMS). This BMS is designed to protect 10-series Li-ion/Li-polymer 18650 battery packs, commonly used in e-bikes and scooters, ensuring safe and efficient battery performance.

Główne cechy obejmują:

• Typ: 10S 36V 15A
• Tryb okablowania: Same port for charge and discharge
• Roboczy pobór mocy: ≤40uA
• Main Circuit Conduction Internal Resistance: ≤15mΩ
• Zakres temperatur: -40 do +80°C
• Ochrona: Disconnection protection included
• Rozmiar kabla: 2.0MM pitch/40CM length

Instrukcje dotyczące instalacji i okablowania

Proper wiring is critical for the safe and correct operation of the BMS. Refer to the wiring diagram carefully. This BMS uses a same-port connection for both charging and discharging.

Obraz: Wiring diagram for the 10S 36V 15A BMS, illustrating connections for battery positive, load, charger, and total battery negative in a same-port configuration. Note that the P- terminal is typically for charging negative.

Ważna uwaga dotycząca okablowania: Customer feedback indicates that the P- terminal on some diagrams may be misleading. For this BMS, the P- terminal is specifically for the charging negative connection. Ensure all connections are secure and correctly polarized before applying power.

Kroki połączenia:

1. Connect the balance wires from your 10-series battery pack to the BMS balance port, starting from B- (total battery negative) and progressing up to B+ (total battery positive).
2. Connect the main B- wire from the BMS to the total negative of your battery pack.
3. Connect the main C- wire from the BMS to the negative terminal of your charger and load.
4. Connect the main B+ wire from the BMS to the total positive of your battery pack.
5. Double-check all connections for correctness and polarity before proceeding.

Instrukcja obsługi

Once correctly wired, the BMS will automatically manage your battery pack's charging and discharging cycles, providing essential protection functions:

• Ochrona przed rozładowaniem:
  • Single battery over-discharge voltage: 2.7V ± 0.08V
  • Continuous working current: 15A
  • Instant protection current: 80A
  • Overcurrent recovery conditions: Charge recovery / Disconnect load
  • Short-circuit recovery conditions: Charge recovery / Disconnect load
• Recharge Protection:
  • Single battery overcharge voltage: 4.25V ± 0.025V
  • Continuous charging current: 15A
  • Zalecana pojemność ładowarkitage: 56 V-60 V
• Ochrona przed przegrzaniem:
  • Charging over temperature default: 63°C
  • Discharge over temperature default: 85°C

The BMS will automatically cut off power if any of these parameters are exceeded, protecting your battery cells from damage. Power will be restored once conditions return to safe levels or after a specific recovery action (e.g., charging for overcurrent/short-circuit).

Konserwacja

To ensure the longevity and optimal performance of your BMS and battery pack:

• Utrzymuj system BMS w czystości, bez kurzu i wilgoci.
• Avoid exposing the BMS to extreme temperatures outside its specified operating range.
• Regularly inspect wiring for any signs of wear, corrosion, or loose connections.
• Aby zapobiec przegrzaniu, należy zapewnić odpowiednią wentylację wokół akumulatora i systemu BMS.
• Do not attempt to modify the BMS circuit board, as this may void any potential warranty and could lead to damage or safety hazards.

Rozwiązywanie problemów

Jeśli napotkasz problemy z systemem BMS, weź pod uwagę następujące kwestie:

• Brak objętości wyjściowejtage:
  • Check all wiring connections, especially the balance wires and main power connections (B-, C-).
  • Sprawdź, czy pojemność akumulatoratage is within the normal operating range and that no individual cell is over-discharged.
  • Ensure the P- terminal is correctly connected as the charging negative, as per the diagram and customer feedback.
• BMS nie ładuje się:
  • Potwierdź głośność ładowarkitage is within the recommended 56V-60V range.
  • Check for over-temperature conditions (charging over temperature default: 63°C).
  • Inspect the charging connections for continuity.
• BMS Not Discharging (Load Not Working):
  • Check for overcurrent or short-circuit conditions. The BMS will recover after the load is disconnected or charging is initiated.
  • Verify that the discharge over temperature (default: 85°C) has not been triggered.
• Nieprawidłowa objętośćtage Odczyty:
  • Ensure your multimeter is calibrated and used correctly.
  • Re-check all balance wire connections for proper seating and contact.

If problems persist after checking these points, consult a qualified technician.

Specyfikacje

Obraz: The GODIYMODULES BMS 10S 36V 15A board, showcasinze względu na kompaktową konstrukcję i punkty połączeń.

Gwarancja i wsparcie

No specific warranty information is provided with this product. For technical support or inquiries, please contact the seller directly through the platform where the product was purchased.