BoxWave ClearTouch Crystal Screen Protector for Autophix 1100 Instruction Manual

1. Wprowadzenie

This manual provides instructions for the proper installation, usage, and maintenance of your BoxWave ClearTouch Crystal Screen Protector for the Autophix 1100 device. Please read these instructions carefully before proceeding with installation.

Zawartość opakowania

• Two (2) ClearTouch Crystal Screen Protectors
• One (1) ClearTouch Applicator Card
• One (1) Microfiber Cleaning Cloth
• One (1) Dust Removing Sticker

Cechy produktu

• Przejrzystość: Provides 99% visual transparency for vibrant color display.
• Ochrona: Shields your device screen from scratches and dust.
• Precyzyjne dopasowanie: Custom-cut to match the exact dimensions of the Autophix 1100.
• Residue-Free: Utilizes a glueless adhesive that leaves no sticky residue upon removal.

2. Instrukcja instalacji

Follow these steps carefully to ensure a smooth and bubble-free installation of your screen protector.

1. Wyczyść ekran swojego urządzenia: Use the provided microfiber cleaning cloth to thoroughly clean the screen of your Autophix 1100. Ensure all dust, fingerprints, and smudges are removed. For stubborn marks, a screen cleaner (not included) can be used sparingly.
2. Usuń kurz: Use the dust removing sticker to lift any remaining dust particles from the screen. Lightly dab the sticker across the screen surface.
3. Peel Back Layer 1: Carefully peel back the protective layer labeled '1' from one end of the screen protector. Avoid touching the adhesive side.
4. Wyrównaj i zastosuj: Align the exposed adhesive edge of the screen protector with one edge of your device screen. Once aligned, slowly and steadily lower the rest of the screen protector onto the device, peeling back layer '1' as you go.
5. Wygładź bąbelki: Use the applicator card to gently push out any air bubbles towards the edges of the screen protector. Start from the center and work your way outwards.
6. Usuń warstwę 2: Once the screen protector is applied and most bubbles are removed, carefully peel off the top protective layer labeled '2'.
7. Final Smoothing: Perform a final pass with the microfiber cloth to remove any remaining small bubbles or smudges on the surface of the newly applied protector.

Notatka: The special low-tack adhesive may take up to 2 days of regular use to fully adhere around the edges, allowing any small air gaps to clear out naturally.

3. Użytkowanie i pielęgnacja

Ogólne zastosowanie

The ClearTouch Crystal screen protector is designed to maintain the original touch sensitivity and display clarity of your Autophix 1100. Operate your device as usual.

Czyszczenie i konserwacja

To clean your screen protector, gently wipe it with the provided microfiber cleaning cloth. For more thorough cleaning, dampen the cloth slightly with water or a screen-safe cleaning solution. Avoid harsh chemicals or abrasive materials, as these can damage the protector's surface.

4. Rozwiązywanie Problemów

• Bąbelki po instalacji: Small bubbles are common immediately after installation. Use the applicator card to push them towards the nearest edge. For very small bubbles, allow 24-48 hours for them to dissipate naturally as the adhesive fully cures.
• Ochrona przed kurzem: If dust particles are trapped under the protector, carefully lift the nearest corner of the protector with a piece of tape, use the dust removing sticker to lift the particle, and then reapply the protector.
• Niewspółosiowość: If the protector is significantly misaligned, you may carefully peel it off, clean both the device screen and the protector (if no dust has adhered to the adhesive side), and attempt reinstallation. The ClearTouch Crystal is designed for reusability and installation forgiveness.

5. Specyfikacje produktu

6. Informacje o pomocy technicznej

For further assistance, technical support, or warranty inquiries regarding your BoxWave ClearTouch Crystal Screen Protector, please contact BoxWave Corporation directly.

Producent: Korporacja BoxWave
Webstrona: www.boxwave.com (Proszę zwrócić się do urzędnika web(Najnowsze informacje kontaktowe znajdziesz na tej stronie.)

Please have your product model (Autophix 1100) and purchase details ready when contacting support.