CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser User Manual

Wstęp

Thank you for choosing the CLOVER D25-B-TL Touchless Water Cooler Purifier Dispenser. This advanced system provides convenient access to purified cold and ambient water. Featuring a GAC filtration system, UV LED self-cleaning, and touchless dispense technology, it ensures a hygienic and refreshing hydration experience. This manual provides essential information for proper setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your dispenser.

Rycina 1: Przód view of the CLOVER D25-B-TL Water Cooler Dispenser.

Ważne informacje dotyczące bezpieczeństwa

Przed użyciem urządzenia należy uważnie przeczytać wszystkie instrukcje. Zachowaj tę instrukcję do wykorzystania w przyszłości.

• Bezpieczeństwo elektryczne: Ensure the dispenser is connected to a grounded electrical outlet. Do not use extension cords. Disconnect power before cleaning or servicing.
• Podłączenie wody: Connect the dispenser only to a potable water supply. Ensure all connections are secure to prevent leaks.
• Umieszczenie: Place the dispenser on a flat, stable surface. Allow adequate clearance around the unit for ventilation.
• Dzieci i zwierzęta: Keep children and pets away from the dispenser, especially during operation and maintenance.
• Temperatura: This unit dispenses cold and ambient water only. It does NOT produce hot water.
• Szkoda: Do not operate the dispenser if it has a damaged cord or plug, or if it has been dropped or damaged in any way. Contact customer support.

Zawartość opakowania

Sprawdź, czy w przesyłce znajdują się wszystkie elementy wymienione poniżej.

• CLOVER D25-B-TL Water Cooler Dispenser
• First Filter (GAC Purification System)
• Rury wodne
• Złącza
• Emergency Shutoff Valve
• Tubing Clips
• Instrukcja obsługi

Figure 2: Included installation kit components.

Instrukcje konfiguracji

1. Rozpakowywanie: Carefully remove the dispenser and all components from the packaging. Retain packaging for future transport if needed.
2. Umieszczenie: Position the freestanding dispenser on a level, stable surface. Ensure there is adequate space around the unit for proper ventilation, especially at the rear where the cooling coils are located. The dimensions are approximately 13.58"D x 12.2"W x 43.3"H.
3. Instalacja filtra:
   • Locate the filter housing, typically at the rear or bottom access panel of the unit.
   • Insert the provided GAC purification filter into the housing as per the arrows indicating water flow.
   • Secure the filter firmly.
   

   Rysunek 3: Wewnętrzne view illustrating filter placement and water tubing.
4. Podłączenie do sieci wodociągowej:
   • Connect the water tubing from your potable water source to the dispenser's inlet using the provided connectors and emergency shutoff valve.
   • Ensure all connections are tight to prevent leaks. Use tubing clips to secure the tubing if necessary.
   • Slowly open the water supply valve to allow water to fill the dispenser's internal tank. Check for any leaks.
5. Podłączenie zasilania: Podłącz dozownik do uziemionego gniazdka prądu zmiennego 120 V.
6. Początkowe płukanie: Before first use, dispense several cups of water from both cold and ambient spouts to flush the system and filter. Discard this water.

Instrukcja obsługi

The CLOVER D25-B-TL features touchless dispense and UV LED self-cleaning for enhanced hygiene.

1. Włączanie: Once plugged in, the dispenser will begin to cool the water. Allow approximately 1-2 hours for the water to reach optimal cold temperature (35.6°F).
2. Dispensing Water (Touchless):
   • Place your cup or container under the desired spout (cold or ambient).
   • Wave your hand in front of the sensor located above the spout. The water will begin to dispense.
   • Remove your hand to stop the water flow.
   

   Figure 4: Detail of the touchless dispense spouts and sensors.

3. UV LED Self-Cleaning: The dispenser is equipped with a UV LED self-cleaning system for enhanced water purification. This system operates automatically to maintain the hygiene of the internal water tanks. Refer to the indicator lights on the top panel for its status.

Konserwacja

Regular maintenance ensures the best performance and water quality from your dispenser.

1. Wymiana filtra:
   • The GAC purification filter should be replaced periodically, typically every 6 months or as indicated by the dispenser's filter change indicator (if present).
   • Turn off the water supply and unplug the dispenser before replacing the filter.
   • Follow the filter installation steps in the Setup section to replace the old filter with a new one.
   • Flush the new filter as described in the Initial Flush step.
2. Czyszczenie tacki ociekowej: The ABS drip tray is easily removed for cleaning.
   • Pull the drip tray forward to remove it.
   • Empty any collected water and wash the tray with mild soap and water.
   • Dokładnie wypłucz i ponownie załóż tackę.
3. Czyszczenie zewnętrzne: Przetrzyj zewnętrzne powierzchnie miękką, damp ściereczka. Nie należy używać środków czyszczących o właściwościach ściernych ani rozpuszczalników.
4. Internal Tank Cleaning: The UV LED self-cleaning system helps maintain internal hygiene. For additional cleaning, consult the manufacturer's website or customer support for specific instructions.

Rozwiązywanie problemów

Przed skontaktowaniem się z obsługą klienta zapoznaj się z poniższymi typowymi problemami i rozwiązaniami:

Specyfikacje

Rysunek 5: Wymiary produktu do celów referencyjnych.

Gwarancja i obsługa klienta

For warranty information, product registration, or technical assistance, please contact CLOVER customer support.

Producent: Koniczyna
Webstrona: CLOVER Official Store (dla ogólnych informacji o produkcie)
Szczegółowe warunki gwarancji i dane kontaktowe znajdziesz w dokumentacji zakupu.