ELING Universal 85mm Digital GPS Speedometer Odometer User Manual

Wstęp

This manual provides detailed instructions for the installation, operation, and maintenance of your ELING Universal 85mm Digital GPS Speedometer Odometer. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the device.

The ELING Digital GPS Speedometer Odometer is designed for a wide range of vehicles including racing cars, RC motorcycles, trucks, and boats, operating on 12V or 24V systems. It features a digital display with 7-color backlight, adjustable overspeed alarm, and precise GPS-based speed and mileage tracking.

Produkt ponadview

The ELING 85mm Digital GPS Speedometer Odometer provides accurate speed, course over ground (COG), odometer, and trip meter readings. It is equipped with a GPS antenna for signal acquisition and an external button for settings adjustment.

Przód view of the ELING 85mm Digital GPS Speedometer Odometer, showing the digital display.

Various backlight color options available on the ELING 85mm Digital GPS Speedometer Odometer.

Konfiguracja i instalacja

Careful installation is crucial for the proper functioning of your GPS speedometer. Follow these steps:

1. Przygotuj otwór montażowy: Open an 85mm (3 3/8 inch) diameter hole in your dashboard. Ensure there is a clearance of at least 55mm (2 3/16 inch) behind the panel to accommodate the gauge body.
   

   Diagram illustrating the required dashboard hole dimensions and clearance for the gauge.

2. Zainstaluj wskaźnik: Insert the gauge into the prepared hole from the front of the dashboard. Secure it in place using the fastening ring provided, tightening it from the rear of the panel.
   

   Strona view of the speedometer, illustrating the threaded body for secure panel mounting.

3. Podłącz okablowanie: Zapoznaj się z poniższym schematem okablowania.
   • Czarny przewód: Podłącz do uziemienia (GND).
   • Czerwony przewód: Connect to Power (+).
   • Zielony przewód: Connect to external button (+).
   • Biały drut: Connect to external button (-).
   

   Tył view of the speedometer with labeled wiring connections.

4. Montaż anteny GPS: Securely fasten the GPS antenna in a location with a clear view of the sky. This is typically outdoors or inside the front windscreen. Connect the antenna cable to the designated socket on the back of the gauge. Do not cut the antenna cable.
   

   The speedometer unit shown with its GPS antenna and optional external button.

5. Pierwsze włączenie: After completing all connections, apply power to the speedometer. Allow approximately 1 minute for the gauge to acquire a GPS satellite signal.

Important Note for Settings Adjustment:

When adjusting settings that require power cycling (e.g., Odometer, Buzzer, Unit), you must disconnect both the Power (+) and Ground (-) wires before making the adjustment, and then reconnect them. If you only cut power to the positive wire, the settings may not save correctly.

Original user manual diagram, providing a visual summary of installation and basic operation steps.

Instrukcja obsługi

The ELING GPS Speedometer offers several adjustable functions for personalized use.

• Changing Backlight Color:

  With the speedometer powered on, press and hold the button located on the back of the gauge (or the external button if installed) for 5-6 seconds. The backlight color will change. Release the button and press it again for 5-6 seconds to cycle through the available 7 colors.

• Function Selection (ODO, BUZZ, UNIT):

  To access the main function settings, press and hold the button on the back of the gauge (or external button) while turning on the power supply. The LCD will display "ODO", "BUZZ", or "UNIT". Release the button when the desired function is displayed.

  • ODO (Change Total Odometer):

    After selecting "ODO", the LCD will show "0000" (or your current odometer value). Press the button to change the flashing digit. Continue pressing to cycle through digits and set your target odometer value. This setting requires power cycling as noted above.

  • BUZZ (Change Overspeed Buzzer Alarm Threshold):

    After selecting "BUZZ", the LCD will show "B 00" (or your current threshold). Press the button to change the flashing digit. The overspeed buzzer alarm threshold can be set from 10 to 240. This setting requires power cycling as noted above.

  • UNIT (Switch Speed Unit):

    After selecting "UNIT", the LCD will display the current speed unit (KM/H, MPH, or Knots). Press the button to cycle through the available units and select your preferred one. This setting requires power cycling as noted above.
• Resetting Trip Odometer to Zero:

  To reset the trip odometer, press the button on the back of the gauge (or external button) for 2-3 seconds. The trip odometer will then reset to zero.

Specyfikacje

Rozwiązywanie problemów

• Brak zasilania/Wyświetlacz nie świeci się:

  Check all wiring connections, especially the red (power) and black (ground) wires, to ensure they are securely connected and receiving the correct voltage (9-32V DC). Verify the power source is active.

• No GPS Signal/Speed Not Displaying:

  Ensure the GPS antenna is securely connected to the gauge and placed in a location with a clear, unobstructed view of the sky. Allow up to 1 minute for initial signal acquisition. Obstructions like metal roofs or dense foliage can interfere with the signal.

• Settings Not Saving (Odometer, Buzzer, Unit):

  Remember to disconnect both the positive power and ground wires before making adjustments to these settings, and then reconnect them. Only disconnecting the positive wire may prevent settings from being saved.
• Display Condensation/Water Ingress:

  While the product is designed for durability, ensure proper sealing during installation, especially in marine or outdoor environments. If condensation occurs, check the integrity of the gauge's mounting and seals. Contact support if the issue persists after verifying installation.

• Numbers Hard to Read in Certain Backlight Colors:

  Experiment with different backlight colors by holding the button for 5-6 seconds to find the color that offers the best readability in your specific lighting conditions.

Konserwacja

The ELING Digital GPS Speedometer Odometer is designed for low maintenance. Regular care includes:

• Czyszczenie: Przetrzyj wyświetlacz i obudowę miękką ściereczką.amp szmatką. Unikaj środków czyszczących o działaniu ściernym i rozpuszczalników, które mogłyby uszkodzić plastik.
• Kontrola połączenia: Periodically inspect wiring connections for corrosion or looseness, especially in high-vibration environments.
• Umiejscowienie anteny: Ensure the GPS antenna remains securely mounted and has an unobstructed view nieba dla optymalnej wydajności.

Gwarancja i wsparcie

For warranty information, please refer to the documentation included with your purchase or contact the seller directly. ELING products typically come with a standard manufacturer's warranty against defects in materials and workmanship.

If you encounter any issues not covered in this manual or require further assistance, please contact ELING customer support or your authorized dealer. You can often find contact information on the product packaging or the official ELING brand store online.

Visit the official ELING store for more information: ELING Store