Transformers Studio Series Core Starscream Action Figure Instruction Manual

Wstęp

This manual provides instructions for the assembly, transformation, and care of your Transformers Studio Series Core Starscream action figure. This collectible figure, inspired by the Transformers: Bumblebee movie, converts between robot and jet modes. Please read these instructions carefully to ensure proper use and enjoyment of your figure.

Informacje dotyczące bezpieczeństwa

Ostrzeżenie: Niebezpieczeństwo zadławienia – mogą powstawać drobne elementy. Nieodpowiednie dla dzieci poniżej 3 lat.

This product contains small components that could pose a choking hazard. Adult supervision is recommended for children aged 8 and up. Keep all packaging materials away from children.

Zawartość opakowania

• 1x Starscream Action Figure (Model F8750)
• 1x Blaster Accessory

Image: The product packaging for the Transformers Studio Series Core Starscream figure, showing the figure in robot mode and the Studio Series branding.

Organizować coś

Your Starscream figure comes pre-assembled in robot mode. No additional assembly is required beyond removing it from the packaging. The included blaster accessory can be attached to the figure's hand in robot mode or stored in jet mode.

Image: The Starscream figure in its robot mode, holding the blaster accessory in its right hand, posed dynamically.

Obsługa: Instrukcje transformacji

The Starscream figure converts between robot mode and jet mode in 14 steps. Follow these instructions carefully to avoid damage to the figure.

Converting from Robot Mode to Jet Mode

1. Remove Blaster: Detach the blaster accessory from the figure's hand. Set it aside for later attachment in jet mode.
2. Pozycja ramion: Rotate the robot's arms downwards and inward, aligning them with the body.
3. Złóż ręce: Fold the robot's hands into the forearms if they are not already retracted.
4. Obrót talii: Carefully rotate the upper body at the waist 180 degrees.
5. Dostosuj skrzydła: Fold the wings on the robot's back upwards and slightly inward.
6. Pozycja nóg: Bring the robot's legs together.
7. Fold Feet: Fold the robot's feet upwards to align with the shins.
8. Compress Legs: Compress the lower leg sections into the upper leg sections.
9. Form Jet Nose: The chest section of the robot will form the nosecone of the jet. Extend it forward.
10. Connect Legs to Torso: Securely connect the transformed leg section to the back of the jet mode, ensuring all tabs and slots align.
11. Align Arms: Position the arms along the sides of the jet mode, ensuring they are flush with the main body.
12. Final Wing Adjustment: Adjust the wings to their final position for jet mode, ensuring they are symmetrical.
13. Attach Blaster: The blaster accessory can be attached to a designated port underneath the jet mode, typically near the rear.
14. Verify Transformation: Ensure all parts are securely tabbed and aligned to form a cohesive jet mode.

Image: The Starscream figure fully transformed into its jet mode, viewz góry, pokażasing its sleek design and integrated blaster.

Image: The Starscream figure in jet mode, viewed from the rear, highlighting the thrusters and wing structure.

Converting from Jet Mode to Robot Mode

To convert back to robot mode, reverse the steps above. Pay attention to the alignment of tabs and slots during each step.

1. Remove Blaster: Detach the blaster from the jet mode.
2. Separate Body Sections: Carefully unclip the leg section from the main jet body.
3. Wyprostuj nogi: Extend the compressed leg sections and unfold the feet.
4. Separate Arms: Unclip and position the arms away from the jet body.
5. Retract Jet Nose: Fold the jet nosecone back into the robot's chest area.
6. Obrót talii: Rotate the upper body 180 degrees to face forward.
7. Unfold Hands: Wyciągnij ręce robota z przedramion.
8. Pozycja ramion: Bring the arms down to the robot's sides.
9. Dostosuj skrzydła: Position the wings on the robot's back as desired for robot mode.
10. Attach Blaster: Place the blaster accessory into either of the robot's hands.
11. Verify Transformation: Ensure all joints are locked and the figure stands stably in robot mode.

Image: The Starscream figure in its robot mode, standing upright, showcasing its detailed design without the blaster.

Konserwacja

• Czyszczenie: Wipe the figure with a soft, dry cloth to remove dust. For stubborn dirt, a slightly damp Można użyć ściereczki, a następnie natychmiast wysuszyć. Unikać silnych środków chemicznych i ściernych środków czyszczących.
• Składowanie: Przechowuj figurkę w miejscu niedostępnym dla dzieci, chroniąc ją przed bezpośrednim działaniem promieni słonecznych i ekstremalnymi temperaturami, aby zapobiec odbarwieniu lub odkształceniu plastikowych części.
• Obsługiwanie: Handle the figure by its main body parts. Avoid excessive force on small joints or thin components during transformation to prevent breakage.

Rozwiązywanie problemów

• Trudność transformacji: If a part feels stuck, do not force it. Re-examine the previous steps to ensure correct alignment. Sometimes, a slight adjustment or rotation is needed before a part can move freely.
• Luźne stawy: Over time, some joints may become slightly loose. This is normal with repeated use. For minor looseness, a small amount of clear nail polish or a similar friction-enhancing liquid can be applied to the joint and allowed to dry completely.
• Akcesoria do mocowania: If the blaster accessory does not fit securely, ensure it is oriented correctly and inserted into the designated port.

Specyfikacje

Gwarancja i wsparcie

For warranty information, product support, or to inquire about replacement parts, please refer to the official Hasbro webOdwiedź stronę internetową lub skontaktuj się bezpośrednio z działem obsługi klienta. Szczegółowe warunki gwarancji mogą się różnić w zależności od regionu i sprzedawcy.

Oficjalna marka Webstrona: Oficjalny sklep Transformers