Lemon RX LM0086VP DSMP 7-Channel Receiver Instruction Manual

1. Koniec produktuview

The Lemon RX LM0086VP is a generation 2 DSMP 7-channel full-range telemetry stabilizer receiver. It offers compatibility with DSMX and DSM2 systems, providing advanced features for responsive control in both electric and gasoline engine applications.

Główne cechy:

• Technologia: DSMP with GEN2 SDR stack (DSMX / DSM2 compatibility).
• Kanały: 7-channel full-range telemetry stabilizer.
• Telemetria: Integrated Barometer, Altimeter, Energy meter (requires V/I sensor), and Internal Temperature Sensor.
• Stabilizacja: High sensitivity gyro with proprietary algorithm for responsive control.
• Moc: BEC1 and BEC2 dual inputs for high-reliability operation and high current drain servos.
• Miksery: Built-in Delta, V-tail, and Normal Wing mixers.
• Aileron Support: Supports stabilization with separated channel dual aileron operation.
• Stabilization Control: Always-on feature with real-time variable stabilization gain control on channel 8.
• Bezpieczny: All-channel failsafe.
• Niezawodność sygnału: Antenna diversity and satellite port for additional signal diversity.
• Gyro Activation: Via AUX2 or Gear channel.
• Gain Tuning: 3 potentiometers for individual gain tuning.

Figure 1: Lemon RX LM0086VP DSMP 7-Channel Receiver with connected wires.

2. Konfiguracja i wiązanie

2.1. Basic Binding Procedure

1. Ensure your transmitter is set to the correct protocol (DSMP, DSMX, or DSM2).
2. Insert the bind plug into Channel 6 on the receiver.
3. Power on the receiver. The LEDs on the receiver will flash, indicating it is in bind mode.
4. Rozpocznij proces wiązania w swoim nadajniku.
5. Once bound, the receiver LEDs will stop flashing and remain solid.
6. Wyjmij wtyczkę powiązania z odbiornika.

2.2. Failsafe Setup

The default failsafe setting is 'no pulses'. To customize failsafe positions:

1. With the receiver bound and powered on, position your transmitter sticks and switches to the desired failsafe positions (e.g., mid-throttle, slight elevator up).
2. Press and hold the 'F' button on the receiver for approximately 3 seconds until the blue light illuminates.
3. Release the 'F' button. The failsafe positions are now set.
4. To revert to 'no pulses' failsafe, press and hold the 'F' button again until the blue light turns off.

2.3. Stabilization Type Setup

To configure the stabilization for your aircraft type (e.g., conventional tail, Delta, V-tail):

1. Insert the bind plug into Channel 6.
2. Press and hold the 'C' button on the receiver while powering it on.
3. All six programming LEDs (three red, three blue) will flash.
4. Press the 'C' button repeatedly to cycle through the different tail types. The illuminated LEDs (e.g., R1 and R2 for conventional tail) will indicate the selected type.
5. Once your preferred tail type is indicated by the LEDs, press the 'C' button twice quickly to save the setting. The lights will then remain solid.

2.4. Master Gain Control Setup

To assign a switch or dial on your transmitter for real-time variable stabilization gain control (Channel 8):

1. With the receiver bound and powered on, insert the bind plug into Channel 5.
2. Press and hold the 'C' button on the receiver while powering it on.
3. All six programming LEDs will flash.
4. The LEDs will indicate the assigned channel for master gain (e.g., green for Channel 7, blue for Channel 5). Press 'C' to cycle if needed.
5. On your transmitter, go to the 'Mixes' menu.
6. Add a new mix for Channel 8.
7. Set the source for this mix to your desired switch or dial (e.g., S1 dial for variable control).
8. The receiver's green status light will indicate that stabilization is active and controllable via the assigned channel.

2.5. Telemetry Setup (Voltage Probe)

To enable full-range telemetry, including battery voltagmonitorowanie:

1. Podłącz głośnośćtage probe to the designated port on the receiver (labeled 'Voltage Probe' or similar).
2. Connect the other end of the voltage probe to the positive lead of your aircraft's battery balance cable.
3. Power on the receiver and transmitter.
4. After approximately 60 seconds, the transmitter should display telemetry data, including battery voltage.

3. Obsługa odbiornika

3.1. Stabilization Activation

Once configured, the stabilization feature can be activated or deactivated during flight using the assigned switch on your transmitter (e.g., Channel 7 or AUX2/Gear channel). When stabilization is active, the receiver's green status light will be on.

3.2. Adjusting Master Gain

The master gain for stabilization can be adjusted in real-time using the assigned dial or switch on your transmitter (Channel 8). This allows for fine-tuning the level of stabilization to suit flying conditions and personal preference.

3.3. Monitoring Telemetry

Telemetry data, including battery voltage, altitude, and internal temperature, can be monitored directly on your compatible transmitter's display. This provides critical real-time information about your aircraft's status during flight.

4. Konserwacja

4.1. Przywracanie ustawień fabrycznych

If you need to use the receiver in a new aircraft or wish to clear all previous settings, you can perform a factory reset:

1. Upewnij się, że odbiornik jest wyłączony.
2. Press and hold both the 'B' and 'F' buttons simultaneously.
3. While holding the buttons, power on the receiver.
4. Continue holding the buttons until all LEDs on the receiver illuminate.
5. Release the buttons. The receiver has now been factory reset to its default settings.

4.2. Ogólna opieka

• Keep the receiver dry and away from moisture.
• Unikaj wystawiania odbiornika na działanie ekstremalnych temperatur.
• Regularnie sprawdzaj wszystkie połączenia pod kątem pewności mocowania i oznak zużycia.

5. Rozwiązywanie Problemów

• Odbiorca nie jest zobowiązany: Ensure the transmitter is set to the correct protocol (DSMP, DSMX, or DSM2) and the bind plug is correctly inserted. Try rebinding.
• No telemetry data: Sprawdź objętośćtage probe is correctly connected to both the receiver and the battery balance cable. Check transmitter settings for telemetry display.
• Stabilization not active: Confirm the stabilization channel (e.g., Channel 7) is correctly assigned and activated on your transmitter. Check the receiver's green status light.
• Incorrect control response: Perform a factory reset and reconfigure all settings, paying close attention to tail type and channel assignments.

6. Specyfikacje techniczne

7. Gwarancja i wsparcie

For detailed warranty information and additional support resources, please refer to the official Lemon RX website. This manual provides operational guidance; specific warranty terms are subject to the manufacturer's policy.

Aby uzyskać dalszą pomoc, odwiedź stronę: www.lemon-rx.com/manual