ZÜNDAPP Kingmeter LED Display T320 Green 1.0 / Z101 / Z101+ User Manual

Wstęp

This manual provides essential information for the proper installation, operation, and maintenance of your ZÜNDAPP Kingmeter LED Display. This display is compatible with ZÜNDAPP Green 1.0, Z101, and Z101+ electric bicycles manufactured from July 2021 onwards. Please read these instructions carefully before use to ensure optimal performance and safety.

Produkt ponadview

The ZÜNDAPP Kingmeter LED Display serves as the central control unit for your electric bicycle, providing critical information and allowing you to manage assistance levels.

ZÜNDAPP Kingmeter LED Display front view z guzikami

Obraz: Przód view of the ZÜNDAPP Kingmeter LED Display, showing the power button, assist level buttons (+/-), and light control button. LED indicators for power and assist levels are visible at the top.

The display unit includes:

Wskaźniki LED: For battery charge level and pedal assistance level.
Przyciski sterujące: Four buttons for power, assistance level adjustment, and light control.
Kabel: A 220 mm cable with a 5-pin round BUS connector.

Konfiguracja i instalacja

Follow these steps to properly install the Kingmeter LED Display on your electric bicycle.

Montaż wyświetlacza:
The display features a 22.2 mm clamp, suitable for most standard bicycle handlebars. Position the display on your handlebar in a location that is easily accessible and visible while riding, without obstructing other controls. Securely tighten the clamp śruby.
Obraz: Zbliżenie view of an electric bicycle handlebar with the ZÜNDAPP Kingmeter LED Display mounted. The display is centrally positioned for easy access and visibility.
Podłączanie kabla:
Locate the corresponding 5-pin round BUS connector on your electric bicycle's wiring harness. Carefully align the pins and push the display's connector firmly into place until it clicks. Ensure a secure connection to prevent moisture ingress and signal loss.

Obraz: Szczegółowy view of the 5-pin round BUS connector, showing the pin configuration. This connector is used to link the display to the e-bike's electrical system.
Obraz: The rear side of the ZÜNDAPP Kingmeter LED Display, showing the integrated cable and a sticker indicating "36V", confirming its voltage kompatybilność.

Instrukcja obsługi

The Kingmeter LED Display features a simple 4-button interface for easy operation.

ZÜNDAPP Kingmeter LED Display with labeled buttons

Obraz: Czysty view of the ZÜNDAPP Kingmeter LED Display, highlighting the four control buttons: Power (red), Plus (+), Minus (-), and Light (headlight icon). LED indicators for battery and assist levels are also visible.

Włączanie/wyłączanie: Naciśnij i przytrzymaj czerwony przycisk zasilania (⑂) to turn the display and the e-bike system on or off.
Adjusting Assistance Level:
- Naciśnij przycisk „+” to increase the pedal assistance level.
- Naciśnij '-' przycisk to decrease the pedal assistance level.
- The current assistance level (0, 1, 2, 3) is indicated by the LED lights. Level 0 means no assistance.
Sterowanie oświetleniem: Naciśnij przycisk światła (🚲) to turn your e-bike's lights on or off.
Wskaźnik poziomu baterii: The "POWER" LED indicators at the top of the display show the remaining battery charge. "LOW" indicates a low battery level.

Konserwacja

To ensure the longevity and proper functioning of your Kingmeter LED Display, follow these simple maintenance guidelines:

Czyszczenie: Wipe the display surface with a soft, damp ściereczką. Nie używaj środków czyszczących o działaniu ściernym ani rozpuszczalników, ponieważ mogą one uszkodzić elementy plastikowe i elektroniczne.
Ochrona przed wilgocią: While the display is designed for outdoor use, avoid prolonged exposure to heavy rain or direct water jets. Ensure the connector is always securely fastened.
Kontrola kabla: Periodically check the cable and connector for any signs of wear, damage, or corrosion. Replace if necessary.
Składowanie: Jeśli rower elektryczny nie będzie używany przez dłuższy czas, należy przechowywać go i wyświetlacz w suchym i umiarkowanym miejscu.

Rozwiązywanie problemów

If you encounter issues with your Kingmeter LED Display, refer to the following common problems and solutions:

Problem	Możliwa przyczyna	Rozwiązanie
Wyświetlacz się nie włącza.	Low or empty e-bike battery. Loose or disconnected cable. Faulty display or e-bike system.	Charge the e-bike battery. Check the 5-pin connector for a secure connection. Contact customer support if the issue persists after checking battery and connection.
No pedal assistance.	Assistance level set to 0. Battery low or empty. Problem z czujnikiem.	Increase assistance level using the '+' button. Charge the e-bike battery. Inspect pedal assist sensor for damage or obstruction.
Światła nie włączają się.	Światła są wyłączone. Loose light connection. Faulty lights.	Press the light button to activate. Check light wiring connections. Consult a technician if lights remain unresponsive.

If you cannot resolve the issue using the troubleshooting guide, please contact ZÜNDAPP customer support or an authorized service center.

Specyfikacje

Funkcja	Szczegół
Model	Kingmeter T320 Green 1.0 / Z101 / Z101+
Zgodność	ZÜNDAPP Green 1.0 / Z101 / Z101+ electric bicycles (from July 2021)
Typ wyświetlacza	PROWADZONY
Typ złącza	5-pin round BUS connector
Długość kabla	220 mm
Clamp Średnica	22.2 mm
Wymiary (szer. x wys.)	50 mm x 51.5 mm (approximate)
Materiał główny	Plastikowy
Kolor	Czarny

Gwarancja i wsparcie

For warranty information, please refer to the documentation provided with your electric bicycle or contact your point of purchase. For technical support or service inquiries, please visit the official ZÜNDAPP webstronie lub skontaktuj się z działem obsługi klienta.

Notatka: Unauthorized modifications or repairs may void your warranty.

ZÜNDAPP Kingmeter T320 Green 1.0 / Z101 / Z101+