Waveshare CM4-DUAL-ETH-MINI Base Board User Manual

1. Wprowadzenie i koniecview

The Waveshare CM4-DUAL-ETH-MINI is a compact and practical baseboard designed for use with the Raspberry Pi Compute Module 4 (CM4). This board is engineered to provide dual Gigabit Ethernet capabilities, making it ideal for applications requiring multiple network interfaces, such as soft routing, network gateways, or industrial control systems.

It is suitable for evaluating the Raspberry Pi CM4 and for integration into various end products, offering a robust and neat solution for expanding the CM4's connectivity.

Rysunek 1: Koniecview of the CM4-DUAL-ETH-MINI Base Board, highlighting its compact design and dual Ethernet ports.

2. Główne cechy

The CM4-DUAL-ETH-MINI baseboard offers a comprehensive set of features to enhance the functionality of your Raspberry Pi Compute Module 4:

• CM4 Socket: Compatible with all variants of the Raspberry Pi Compute Module 4.
• Dual Gigabit Ethernet Ports: Two RJ45 connectors supporting 10/100/1000M networking, powered by an RTL8111H Gigabit NIC chip. ETH0 serves as the CM4 original network port, and ETH1 as a PCIe extended network port.
• Port USB 2.0 typu A: A single USB 2.0 port for connecting peripheral devices.
• 40PIN GPIO Header: Standard Raspberry Pi 40-pin interface for connecting various HATs and expansion modules.
• Gniazdo kart Micro SD: For Compute Module 4 Lite (without eMMC) variants, allowing for OS storage.
• Fan Header: A 4-wire SH1.0 port for connecting a cooling fan, supporting speed adjustment and measurement (5V fans only).
• Port typu C: Functions as a 5V/2.5A power supply input and a USB interface for eMMC programming.
• Przycisk resetowania: For convenient system reset.
• BOOT Switch: Allows switching between booting from the USB-C interface (ON position) or from eMMC/Micro SD card (OFF position).
• Przełącznik SYSTEM: Includes options for EEPROM write protection (EEPROM_WP), disabling Wi-Fi (WIFI_DIS), and disabling Bluetooth (BT_DIS) for CM4 versions with wireless capabilities.

Figure 2: Detailed diagram illustrating the various interfaces and components on the CM4-DUAL-ETH-MINI board.

Rysunek 3: Widok z góry na dół view of the board with numbered components and their descriptions.

3. Konfiguracja i instalacja

Follow these steps to properly set up and install your Waveshare CM4-DUAL-ETH-MINI baseboard with a Raspberry Pi Compute Module 4.

3.1 Connecting the Compute Module 4

1. Ensure the CM4-DUAL-ETH-MINI baseboard is powered off and disconnected from any power source.
2. Carefully align your Raspberry Pi Compute Module 4 with the CM4 Socket on the baseboard. Ensure the connectors are correctly oriented.
3. Gently press the CM4 into the socket until it is securely seated. Do not force the module.

Figure 4: Illustration of connecting a Raspberry Pi Compute Module 4 to the base board.

3.2 Zasilanie

The CM4-DUAL-ETH-MINI requires a 5V DC power supply via its Type-C interface. For normal operation of the CM4, a 5V/2A power supply is recommended. Insufficient power may lead to issues such as automatic shutdowns or frequency reduction.

When using the Type-C interface to program the CM4's eMMC, ensure no other devices are connected to the baseboard to guarantee stable power delivery during the programming process.

3.3 USB 2.0 Port Activation

By default, the USB 2.0 port is disabled. To enable it, you need to modify the config.txt file on your Raspberry Pi OS. Add the following line to config.txt:

dtoverlay=dwc2,dr_mode=host

3.4 Podłączenie wentylatora

If you plan to use a cooling fan, connect it to the 4-wire SH1.0 fan header. Ważny: Only 5V fans are supported. Confirm your fan's voltage before connecting to prevent damage.

4. Instrukcja obsługi

Once the Compute Module 4 is securely installed and the baseboard is powered, the system will boot according to the BOOT switch setting (eMMC/Micro SD or USB-C for programming). The dual Gigabit Ethernet ports allow for flexible network configurations, such as setting up a router, firewall, or network bridge.

For specific software configurations, refer to the official Raspberry Pi documentation and relevant open-source projects (e.g., OpenWRT for router applications).

Rysunek 5: Byłyample application showing the CM4-DUAL-ETH-MINI with network cables connected, demonstrating its use in a network setup.

5. Konserwacja i bezpieczeństwo

To ensure the longevity and proper functioning of your CM4-DUAL-ETH-MINI baseboard, observe the following guidelines:

• Wyłącz zasilanie przed podłączeniem/odłączeniem: Always power off the device before plugging or unplugging any components, especially the Compute Module 4 or any non-USB peripherals.
• Warunki środowiskowe: Używaj deski w czystym i suchym otoczeniu, z dala od ekstremalnych temperatur, wilgoci i bezpośredniego światła słonecznego.
• Zachowaj ostrożność: Avoid static discharge by handling the board by its edges. Do not apply excessive force to connectors or components.
• Czyszczenie: Use a soft, dry cloth to clean the board. Avoid liquids or abrasive cleaners.

6. Rozwiązywanie Problemów

W tej sekcji omówiono typowe problemy, na które możesz natrafić:

• System Shuts Down or Reduces Frequency:

  Przyczyna: Insufficient power supply to the Compute Module 4.

  Rozwiązanie: Ensure you are using a stable 5V/2A power supply connected to the Type-C port. Avoid connecting other high-power devices to the baseboard when the CM4 is in operation.

• USB 2.0 Port Not Functioning:

  Przyczyna: The USB 2.0 port is disabled by default.

  Rozwiązanie: Refer to Section 3.3 "USB 2.0 Port Activation" and add the necessary line to your config.txt file.

• Wentylator nie kręci się:

  Przyczyna: Incorrect fan voltage or improper connection.

  Rozwiązanie: Verify that your fan is a 5V model. Check the connection to the 4-wire SH1.0 fan header for proper alignment and secure fit.
• Unable to Program CM4 eMMC via Type-C:

  Przyczyna: Other devices drawing power, or BOOT switch in incorrect position.

  Rozwiązanie: Disconnect all other peripherals from the baseboard. Ensure the BOOT switch is set to the "ON" position (boot from USB-C interface) before attempting to program.

7. Specyfikacje

Figure 6: Outline dimensions of the CM4-DUAL-ETH-MINI base board in millimeters.

8. Gwarancja i wsparcie

For detailed technical documentation, user guides, and support resources, please visit the official Waveshare website. An online user manual is available, which should be consulted for comprehensive information and updates.

Waveshare provides a wiki with detailed documentation, including technical drawings and setup guides, to assist users with their products.

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact Waveshare customer support directly.

Oficjalny Waveshare Webstrona: www.waveshare.com