Kadimendium ND0412SA DC-DC Step-up Module

1. Wprowadzenie

This manual provides detailed instructions for the Kadimendium ND0412SA DC-DC Step-up Module. This module is designed to convert a lower DC input voltage (2.6V-5.5V) into a higher, stable DC output voltage (selectable 5V, 6V, 9V, or 12V). It is suitable for various applications requiring a boosted power supply, such as battery-powered equipment, LED motors, and low-power electronic devices.

2. Instrukcje bezpieczeństwa

• Ensure all power sources are disconnected before making any connections to the module.
• Observe correct polarity for input and output connections (V_i, GND, V_o). Incorrect polarity can damage the module and connected devices.
• Nie przekraczaj określonej maksymalnej objętości wejściowejtage or output current ratings.
• Avoid short circuits on the input or output terminals. While the module has short-circuit protection, prolonged short circuits can cause damage.
• Operate the module within its specified temperature range (-40°C to +85°C).
• Trzymaj moduł z dala od wilgoci, kurzu i środowiska korozyjnego.

3. Koniec produktuview

The ND0412SA is a compact and efficient DC-DC boost converter. It features high efficiency (up to 93%) and incorporates multiple protection mechanisms including over current (OCP), over voltage (OVP), short circuit (SCP), and over temperature (OTP) to ensure reliable operation and extend the lifespan of the power supply.

Rysunek 3.1: Góra view of the ND0412SA module, displaying its compact design and main components.

The module's input terminals are labeled V_i (Wprowadź objętośćtage) and GND (Ground). The output terminals are labeled V_o (Wyjściowa objętośćtage) and GND. The bottom side of the module features solder pads for selecting the desired output voltage.

Rysunek 3.2: Dół view of the ND0412SA module, showing the output voltage selection pads.

4. Konfiguracja

Follow these steps to set up your ND0412SA module:

1. Objętość wyjściatagWybór: Before connecting power, select your desired output voltage (5V, 6V, 9V, or 12V) by bridging the corresponding solder pads on the bottom of the module (refer to Figure 3.2). For example, to set the output to 12V, bridge the pad labeled '12V'. If no pads are bridged, the module may default to a specific voltage or operate unpredictably.
2. Połączenie wejściowe: Connect your DC input power source to the V_i and GND input terminals. Ensure the input voltage is within the 2.6V to 5.5V range.
3. Połączenie wyjściowe: Connect your load to the V_o and GND output terminals.
4. Advanced Output Voltage and Current Limit Adjustment (Optional): For custom output voltages or current limits, the module allows adjustment via external resistors R1 and R3. This requires soldering and precise resistor values. Refer to Figure 4.1 for details.
   • Objętość wyjściatage (R1): The R1 resistor sets the output voltage. The formula is R1(KΩ) = 10 * (Vout / 0.6 - 1).
   • Current Limit (R3): The R3 resistor programs the peak switch current. The resistor value should be between 10kΩ and 100kΩ. The current limit will be set from 2.5A to 0.5A. The formula is I_in = 48000 / R3.

Figure 4.1: Diagram for R1 (output voltage) and R3 (current limit) resistor settings.

5. Instrukcja obsługi

Once the module is correctly wired and the output voltage is selected, apply power to the input terminals. The module will automatically boost the input voltage to the selected output voltage. Monitoruj objętość wyjściowątage and current to ensure it meets your application's requirements and stays within the module's specifications.

6. Konserwacja

• Utrzymuj moduł w czystości, bez kurzu i zanieczyszczeń.
• Ensure adequate ventilation, especially when operating at higher loads, to prevent overheating.
• Regularnie sprawdzaj połączenia pod kątem luzów i korozji.
• Avoid physical shock or excessive vibration to the module.

7. Rozwiązywanie Problemów

• Brak objętości wyjściowejtage:
  • Sprawdź objętość wejściowątage to ensure it is within the 2.6V-5.5V range.
  • Verify input and output connections for correct polarity and secure contact.
  • Upewnij się, że objętość wyjściowatage selection pads are correctly bridged.
  • Check for any short circuits on the output. The module's SCP may have activated.
• Nieprawidłowa objętość wyjściowatage:
  • Re-verify the output voltage selection pads.
  • If using custom R1 adjustment, double-check resistor value and soldering.
• Przegrzanie modułu:
  • Zmniejsz obciążenie podłączone do wyjścia.
  • Ensure proper ventilation around the module.
  • Sprawdź, czy wejście voltage is too low, causing the module to draw excessive current.
• Działanie przerywane:
  • Check for loose connections or poor soldering.
  • Ensure the module is not exposed to excessive electromagnetic interference.

8. Specyfikacje

Typical Output Current (Reference Only):

9. Gwarancja i wsparcie

For warranty information or technical support, please refer to the product's purchase documentation or contact the retailer. Keep your proof of purchase for any warranty claims.