M-Wave COLLECTOR P170 Bicycle Wall Mount Instruction Manual

1. Koniec produktuview

The M-Wave COLLECTOR P170 is a robust and versatile wall mount designed for convenient bicycle storage. This mount is engineered to securely hold bicycles with wheel sizes ranging from 26 to 29 inches, provided they do not have a front fender and have a maximum tire width of 3 inches. It features a stable, rotatable design, allowing for a 170° swivel to optimize space. The mount is foldable when not in use, further enhancing space efficiency. It is suitable for electric bicycles, supporting a maximum weight of 30 kg. An integrated rear wheel support protects your wall from dirt and marks.

Figure 1.1: M-Wave COLLECTOR P170 wall mount with a bicycle in position.

2. Informacje dotyczące bezpieczeństwa

Please read and understand all instructions before installation and use. Failure to follow these instructions may result in property damage or injury.

• Przydatność ściany: Ensure the mounting surface (wall) is structurally sound and capable of safely supporting the combined weight of the mount and the bicycle (up to 30 kg). Consult a professional if you are unsure about your wall's capacity.
• Limit wagowy: Do not exceed the maximum weight capacity of 30 kg (66 lbs). Overloading can cause the mount to fail.
• Prawidłowa instalacja: Use appropriate tools and mounting hardware suitable for your specific wall type (e.g., concrete, brick, wood studs). Always drill pilot holes as recommended.
• Bezpieczne elementy złączne: Regularly check all screws and fasteners to ensure they remain tight and secure. Loose fasteners can compromise stability.
• Dzieci i zwierzęta: Keep children and pets away from the installation area during setup and ensure the mounted bicycle is stable and out of reach to prevent accidents.
• Bicycle Compatibility: This mount is designed for bicycles with 26-29 inch wheels, without a front fender, and a maximum tire width of 3 inches. Do not attempt to mount incompatible bicycles.

3. Zawartość opakowania

Przed przystąpieniem do montażu sprawdź, czy wszystkie elementy są obecne i nieuszkodzone. Jeśli brakuje którejkolwiek części lub jest ona uszkodzona, skontaktuj się ze sprzedawcą.

• Main Wall Mount Unit (foldable arm and wall bracket)
• Wspornik tylnego koła
• Sprzęt montażowy (śruby, kotwy ścienne)
• Instrukcja obsługi (ten dokument)

Figure 3.1: Main wall mount unit, extended view.

Figure 3.2: Rear wheel support component.

4. Konfiguracja i instalacja

Follow these steps carefully to install your M-Wave COLLECTOR P170 wall mount.

1. Wybierz lokacje: Select a suitable wall location that is structurally sound and has enough clear space for the bicycle when mounted and rotated. Consider the height to comfortably lift your bicycle onto the mount.
2. Mark Drilling Points for Main Mount: Hold the main wall bracket against the chosen location. Use a pencil to mark the positions for the mounting holes. Ensure the bracket is level.
3. Drill Holes for Main Mount: Using an appropriate drill bit for your wall type and the provided anchors/screws, drill pilot holes at the marked positions.
4. Secure Main Mount: Insert wall anchors (if required) into the drilled holes. Position the main wall bracket and secure it firmly to the wall using the provided screws. Ensure it is tightly fastened and stable.
5. Position Rear Wheel Support: Place your bicycle on the main mount. Mark the position on the wall where the rear wheel support should be installed to prevent the rear wheel from touching the wall. The support should be centered with the rear wheel.
6. Mark and Drill for Rear Wheel Support: Mark the drilling points for the rear wheel support. Drill pilot holes as done for the main mount.
7. Secure Rear Wheel Support: Attach the rear wheel support to the wall using the provided hardware.
8. Kontrola końcowa: Gently test the stability of both the main mount and the rear wheel support. Ensure all screws are tight before hanging your bicycle.

Rysunek 4.1: Ilustracja view of the installed wall mount with a bicycle.

5. Instrukcja obsługi

Using your M-Wave COLLECTOR P170 wall mount is straightforward.

• Unfolding the Mount: If the mount is in its folded position, gently pull the arm outwards until it locks into the extended position.
• Mounting the Bicycle: Carefully lift your bicycle and place the top tube onto the main support arm. Ensure the bicycle is balanced and the rear wheel rests against the rear wheel support.
• Rotating the Bicycle: The main mount allows for a 170° rotation. To adjust the angle, gently push or pull the bicycle to the desired position. The rotation mechanism is designed to hold the bike securely at various angles.
• Folding the Mount (when not in use): To save space, remove the bicycle. Then, gently push the support arm upwards or inwards until it folds flat against the wall.

Figure 5.1: Illustrates the folding and 170° rotation of the mount.

6. Konserwacja

Regular maintenance ensures the longevity and safe operation of your M-Wave COLLECTOR P170 wall mount.

• Czyszczenie: Wipe the mount periodically with a damp Do usuwania kurzu i brudu należy używać ściereczki. Unikać środków czyszczących o działaniu ściernym.
• Kontrola elementów złącznych: Every few months, or if you notice any instability, re-check all mounting screws and fasteners. Tighten them if necessary.
• Ruchome części: The folding and rotating mechanisms are designed for durability. If movement becomes stiff, a small amount of silicone-based lubricant can be applied to the pivot points.

7. Rozwiązywanie Problemów

If you encounter issues with your M-Wave COLLECTOR P170, refer to the following common problems and solutions.

8. Specyfikacje

9. Gwarancja i wsparcie

For detailed warranty information, product support, or to inquire about replacement parts, please refer to the official M-Wave webOdwiedź witrynę lub skontaktuj się ze sprzedawcą, u którego kupiłeś produkt. Zachowaj dowód zakupu na wypadek reklamacji.