Weber Genesis II E/ES 310/610 Series

Weber 66047 Control Knob Kit Instruction Manual

For 2019 and Newer Genesis II E/ES 310/610 Series Grills

1. Wprowadzenie

Niniejsza instrukcja zawiera podstawowe informacje dotyczące prawidłowej instalacji, obsługi i konserwacji urządzenia. Weber 66047 3-Piece Control Knob Kit. Please read these instructions thoroughly before proceeding to ensure correct usage and to maintain the longevity of your grill components.

2. Koniec produktuview

Ten Weber 66047 Control Knob Kit consists of three genuine replacement control knobs designed for specific Weber Genesis II grill models. These knobs allow for precise control over the gas flow to your grill's burners, ensuring optimal cooking performance.

Trzy Weber 66047 control knobs, gray with a red indicator line and chrome trim, showing the front view.

Obraz 1: Przód view z Weber 66047 control knobs.

3. Zgodność

This control knob kit is specifically designed for the following Weber grill models:

  • 2019 and Newer Weber Genesis II E/ES 310 Series Grills
  • 2019 and Newer Weber Genesis II E/ES 610 Series Grills

Each knob has a diameter of 2-3/4 inches and features a 3/8-inch D-shaped hole for shaft connection. Please verify your grill model and existing knob specifications before installation to ensure proper fit.

4. Co znajduje się w pudełku

Twój Weber 66047 Control Knob Kit includes:

  • 3 razy Weber Control Knobs (Part #66047)

5. Konfiguracja i instalacja

Follow these steps to install your new control knobs:

  1. Zapewnij bezpieczeństwo: Before beginning, ensure your grill is completely off and the gas supply is turned off at the propane tank or natural gas line. Allow the grill to cool down if it has been in use.
  2. Remove Old Knobs: Gently pull the existing control knobs straight off the valve stems. They are typically held in place by friction.
  3. Inspect Valve Stems: Check the valve stems for any debris or damage. Clean them if necessary. The valve stems should be D-shaped to match the opening in the new knobs.
  4. Install New Knobs: Align the D-shaped opening on the back of the new Weber control knob with the D-shaped valve stem on your grill. Push the knob firmly onto the stem until it is seated securely. Ensure the red indicator line on the knob points to the 'OFF' position when the valve is closed.
  5. Funkcjonalność testu: Once all knobs are installed, turn on the gas supply. Carefully test each knob by pushing it in and turning it to the 'IGNITE' position to ensure it engages correctly and the burner ignites. Then turn it back to 'OFF'.
Trzy Weber 66047 control knobs, gray with a red indicator line and chrome trim, showing the back view with the D-shaped shaft opening.

Obraz 2: Tył view of the control knobs, illustrating the D-shaped shaft opening for installation.

Exploded diagram of a Weber Genesis II S/SE-310 LP 2017 grill, highlighting the control knob set (item 27) in the parts list.

Image 3: Grill schematic showing the location of the control knob set (item 27).

6. Instrukcja obsługi

The control knobs regulate the gas flow to the grill burners. To operate:

  • Zapłon: Push the knob in and turn it to the 'IGNITE' position (usually indicated by a lightning bolt or flame symbol) to light the corresponding burner.
  • Dostosuj płomień: Once lit, adjust the flame intensity by turning the knob between the 'HIGH' and 'LOW' settings.
  • Wyłączyć coś: To turn off a burner, push the knob in and rotate it to the 'OFF' position.

7. Konserwacja

To keep your control knobs in good condition:

  • Czyszczenie: Clean the knobs regularly with a soft cloth and mild soap and water. Avoid abrasive cleaners or harsh chemicals, as these can damage the finish.
  • Kontrola: Periodically check the knobs for any signs of wear, cracking, or looseness. Replace them if they are damaged or no longer fit securely.

8. Rozwiązywanie Problemów

If you encounter issues with your control knobs:

  • Pokrętło jest luźne: Ensure the knob is fully pushed onto the D-shaped valve stem. If it continues to be loose, the internal mechanism may be worn, and replacement is recommended.
  • Knob Does Not Turn: Do not force the knob. Ensure it is pushed in completely before attempting to turn. If the issue persists, the valve stem or internal valve mechanism may be obstructed or damaged. Consult a qualified technician or Web...wsparcie.

9. Specyfikacje

Numer części66047
Typ produktuPokrętła sterujące
Ilość3 na zestaw
ZgodnośćWeber Genesis II E/ES 310/610 Series Grills (2019 and Newer)
Średnica pokrętła2.75 inches (2-3/4")
Shaft Hole Diameter0.375 inches (3/8") D-hole
KolorSrebrny/Szary
TworzywoPlastic with Chrome Trim

10. Gwarancja i wsparcie

Weber products are manufactured to high-quality standards and come with a manufacturer's warranty. For specific warranty details, claims, or technical support, please refer to the official Weber webstrona lub kontakt Weber customer service directly. Keep your proof of purchase for warranty purposes.

Weber Customer Support: Odwiedzać WebWsparcie er