Instrukcja obsługi taśmy świetlnej LED Lepro LE 50ft RGB 5050

Wstęp

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Lepro LE 50ft RGB 5050 LED Strip Lights. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.

Instrukcje bezpieczeństwa

• Przed instalacją lub konserwacją należy upewnić się, że zasilanie jest odłączone.
• This product is designed for indoor use only. Avoid exposure to water or high humidity.
• Do not connect the LED strip to the power supply while it is still coiled on the reel. Unroll the strip completely before powering on to prevent overheating.
• Use only the provided 12V ETL-listed power adapter. Using an incompatible power supply may damage the product and void the warranty.
• Do not bend the LED strip at sharp angles (less than 90 degrees) to avoid damaging the circuit board or LEDs.
• Przechowywać w miejscu niedostępnym dla dzieci.
• If any damage is observed on the strip or power adapter, discontinue use immediately and contact customer support.

Zawartość opakowania

Image: The complete package contents including two rolls of LED strip lights, a remote control, a power adapter, and fixing clips with screws.

Sprawdź, czy w przesyłce znajdują się wszystkie elementy wymienione poniżej:

• 2 x 24.6ft (total 50ft) RGB 5050 LED Strip Lights
• 1 x IR Remote Controller (44-key)
• 1 x 12V ETL-listed Power Adapter
• 1 x Skrzynka sterownicza
• Zaciski mocujące i śruby
• Instrukcja obsługi (ten dokument)

Specyfikacje

Konfiguracja i instalacja

Aby prawidłowo zainstalować paski świetlne LED, wykonaj następujące czynności:

1. Przygotuj powierzchnię:

   Before attaching the LED strip, ensure the installation surface is clean, dry, and smooth. Wipe the surface with a clean cloth to remove dust or debris. This ensures optimal adhesion of the 3M adhesive backing.

   

   Image: A hand wiping a wooden surface with a cloth, illustrating the first step of surface preparation.

2. Połącz komponenty:

   Connect the 4-pin connector from the LED strip to the control box. Ensure the arrow mark on the strip's connector aligns with the arrow mark on the control box. Then, connect the DC wire from the power adapter to the control box. Finally, plug the power adapter into a standard electrical outlet.

   

   Image: A visual guide demonstrating how to connect the DC wire to the control box and the 4-pin connector to the LED strip, emphasizing arrow alignment.

   Ważny: Ensure the "arrow" mark on the LED strip connector and the "12V" mark on the control box are on the same side for correct polarity.

   

   Image: Detail of the RGB light strip, highlighting the 10mm 4-pin connector and the strong 3M self-adhesive backing for installation.

3. Zamontuj pasek LED:

   Peel off the protective backing from the 3M adhesive on the back of the LED strip. Carefully press the strip onto the prepared surface, applying firm and even pressure along its entire length. For added security, use the included fixing clips and screws at regular intervals, especially around corners or areas with less adhesion.

   

   Image: A hand demonstrating how to peel and attach the LED strip to a surface, showing the adhesive backing.

4. Przygotowanie pilota zdalnego sterowania:

   Before using the remote control, pull out the transparent plastic chip from the battery compartment. This activates the battery.

   

   Image: A close-up showing a hand pulling the transparent plastic chip from the remote control, indicating battery activation.

Film demonstracyjny instalacji

Działanie

Your LED strip lights are controlled by the included 44-key IR remote control. Point the remote directly at the IR receiver on the control box for optimal response.

Obraz: szczegółowy view of the 44-key remote control, showing buttons for power, brightness adjustment, RGB color selection, 6 DIY color buttons, and various dynamic modes like Jump, Fade, Quick, Slow, and Auto.

• Włączanie/wyłączanie: Naciśnij czerwony przycisk zasilania aby włączyć lub wyłączyć światło.
• Regulacja jasności: Użyj przyciski strzałek w górę i w dół (above the R, G, B, W buttons) to increase or decrease brightness.
• Wybór kolorów: Naciśnij dowolny z 20 color buttons to select a static color.
• Kolory DIY:
  1. Naciśnij jeden z DIY1-DIY6 buttons.
  2. Użyj RGB up/down arrows to adjust the intensity of Red, Green, and Blue to create your desired custom color.
  3. Press the same DIY button again to save the custom color.
• Tryby dynamiczne:
  • JUMP3 / JUMP7: Cycles through 3 or 7 colors with a jump effect.
  • FADE3 / FADE7: Fades between 3 or 7 colors.
  • QUICK / SLOW: Adjusts the speed of dynamic modes.
  • AUTOMATYCZNY: Cycles through all available dynamic modes.
  • LAMPA BŁYSKOWA: Flashes through colors.

Konserwacja

• Czyszczenie: Ensure the power is off and unplugged before cleaning. Gently wipe the LED strip with a dry, soft cloth. Do not use liquid cleaners or abrasive materials.
• Składowanie: If storing the lights for an extended period, ensure they are clean and dry. Store in a cool, dry place away from direct sunlight.
• Przyczepność: If the adhesive begins to lose its stickiness, you can reinforce the strip with additional fixing clips or a suitable adhesive tape (not included).

Rozwiązywanie problemów

Gwarancja i wsparcie

Lepro products are designed for quality and reliability. For warranty information, technical support, or any questions regarding your LED strip lights, please contact Lepro customer service through the retailer where the product was purchased or visit the official Lepro webstrona.

Please have your model number (410105-RGB-US) and purchase details ready when contacting support.