Aeotec Recessed Door Sensor 7 (ZW187-A) User Manual

1. Wprowadzenie

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Aeotec Recessed Door Sensor 7 (ZW187-A). This device is a Z-Wave Plus V2 enabled smart sensor designed to discreetly monitor the open/closed status of doors and windows within your smart home system. It integrates advanced Z-Wave 700 series technology for enhanced range, security, and battery efficiency.

2. Koniec produktuview

The Aeotec Recessed Door Sensor 7 is an invisible security solution, designed to be installed within the door or window frame. It consists of two main components: the sensor unit and a magnetic contact. When the magnet moves away from the sensor, it detects an "open" state, and when it returns, it detects a "closed" state. This information is then transmitted wirelessly to your Z-Wave hub.

• Z-Wave Plus V2 (700 Series): Utilizes the latest Z-Wave technology for improved range, faster communication, and lower power consumption.
• SmartStart włączony: Simplifies the pairing process with compatible Z-Wave hubs by scanning a QR code.
• Bezpieczeństwo S2: Provides advanced encryption for secure communication within your Z-Wave network.
• Konstrukcja wpuszczana: Installs discreetly within door or window frames, maintaining aesthetic appeal.
• Długa żywotność baterii: Optimized for extended battery performance, typically 2+ years with standard usage.

Image: The Aeotec Recessed Door Sensor 7, showcasing its invisible installation within a door frame.

Image: A close-up of the Z-Wave 700 Series chip, highlighting the advanced technology within the sensor.

3. Zawartość opakowania

Sprawdź, czy w przesyłce znajdują się wszystkie elementy:

• 1x Aeotec Recessed Door Sensor 7 (ZW187-A) main unit
• 1x Magnetic contact
• 1x CR2 battery (pre-installed or included separately)
• Mounting screws (if applicable)

Image: The product packaging displaying the main sensor unit, magnetic component, and associated branding.

4. Konfiguracja i instalacja

4.1. Instalacja baterii

1. Ostrożnie otwórz czujnik casing.
2. Insert the CR2 battery, ensuring correct polarity. If a plastic pull tab is present, remove it.
3. Zamknij czujnik casing bezpiecznie.

Note: The device uses a CR2 battery, not a CR123A as sometimes mistakenly listed.

4.2. Pairing with a Z-Wave Hub (Inclusion)

The Recessed Door Sensor 7 supports SmartStart for easy pairing and traditional Z-Wave inclusion.

SmartStart Inclusion (Recommended)

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the sensor or its packaging with a controller providing SmartStart inclusion. No further action is required, and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

1. Upewnij się, że Twoja centrala Z-Wave obsługuje funkcję SmartStart.
2. Open your Z-Wave hub's mobile application and select the option to add a new device using SmartStart or by scanning a QR code.
3. Scan the QR code located on the sensor unit or its packaging.
4. Power on the sensor (ensure battery is installed). The sensor will automatically attempt to pair with the hub.

Image: A smartphone scanning the SmartStart QR code on the sensor for simplified pairing.

Manual Inclusion (Traditional Pairing)

1. Place your Z-Wave hub into inclusion/pairing mode (refer to your hub's manual for specific instructions).
2. With the sensor powered on, press the action button on the sensor unit once. The LED indicator may flash to confirm inclusion mode.
3. If successful, your hub will confirm the device has been added.
4. If pairing fails, ensure the sensor is within range of the hub and repeat the process. You may need to exclude the device first if it was previously paired or attempted to pair unsuccessfully.

4.3. Instalacja fizyczna

The Recessed Door Sensor 7 is designed for discreet installation within the door or window frame.

1. Wybierz lokacje: Identify a suitable location on the top edge of your door or window frame where both the sensor and magnet can be recessed. The magnet should be installed in the moving part (door/window) and the sensor in the stationary frame, or vice-versa.
2. Wiercenie otworów: Using an appropriate drill bit (typically 19mm or 3/4 inch), drill two holes approximately 1 inch deep for the sensor and magnet. Ensure the holes are aligned and close enough for the sensor to detect the magnet when the door/window is closed (typically within 1/2 inch).
3. Wstaw komponenty: Gently push the sensor unit and the magnetic contact into their respective drilled holes. Ensure they are flush with the surface.
4. Test: Open and close the door/window to verify that your Z-Wave hub registers the open/closed status correctly. Adjust placement if necessary.

Obraz: Byłyample of the sensor and magnet discreetly installed within a door frame.

5. Działanie

Once successfully installed and paired, the Aeotec Recessed Door Sensor 7 operates automatically:

• Open/Closed Detection: The sensor detects when the magnetic contact moves away from or towards the main sensor unit.
• Raportowanie stanu: Upon detecting a change in state (open or closed), the sensor immediately sends a Z-Wave command to your connected hub, updating its status.
• Automatyzacja: This status can be used by your Z-Wave hub to trigger various automations, such as turning on lights when a door opens, sending notifications, or activating security routines.
• Battery Reporting: The sensor periodically reports its battery level to the Z-Wave hub.

Image: Illustrates the benefit of monitoring doors and windows for family safety and security.

6. Zgodność

The Aeotec Recessed Door Sensor 7 is a Z-Wave Plus V2 device and is compatible with a wide range of Z-Wave certified hubs and gateways. A Z-Wave hub is required for this sensor to function as part of a smart home system.

Known compatible hubs include, but are not limited to:

• Samsung SmartThings
• Wysokość Hubitat
• Fibaro Home Centre 3
• HomeSeer HS3
• Wiara
• Domoticz
• Open Z-Wave
• ISY994i
• Google Assistant (via compatible hub)
• Amazon Alexa (via compatible hub)

Image: Visual representation of various smart home platforms and voice assistants compatible with the sensor.

Image: Depicts a Z-Wave USB stick and a Z-Wave hub, indicating that a smart hub is necessary for the sensor's functionality.

7. Konserwacja

7.1. Wymiana baterii

The sensor is designed for long battery life (typically 2+ years). When the battery level is low, your Z-Wave hub should report this status. To replace the battery:

1. Carefully remove the sensor unit from its recessed position.
2. Otwórz casing.
3. Wyjmij starą baterię CR2.
4. Włóż nową baterię CR2, zwracając uwagę na prawidłową polaryzację.
5. Zamknij casing and re-insert the sensor into its position.
6. Verify the battery status updates on your Z-Wave hub.

Note: Some users have reported issues with battery life or reporting. Ensure your Z-Wave hub's firmware and device handlers are up-to-date for optimal performance.

Image: A visual emphasizing the sensor's instant wake-up feature and long battery life.

8. Rozwiązywanie Problemów

If you encounter issues with your Aeotec Recessed Door Sensor 7, consider the following:

9. Specyfikacje

10. Gwarancja i wsparcie

Produkty Aeotec zostały zaprojektowane z myślą o niezawodności i wydajności. Szczegółowe informacje dotyczące gwarancji można znaleźć w karcie gwarancyjnej dołączonej do produktu lub na oficjalnej stronie Aeotec. webstrona.

For technical support, troubleshooting assistance, or to access the latest documentation and firmware updates, please visit the official Aeotec support portal:

Wsparcie Aeotec Webstrona

You can also find additional resources and community forums on the Aeotec webstrona: aeotec.pl