Wstęp
This manual provides detailed instructions for the ASHATA DC 12V Digital Relay Board. This versatile module is designed for various timing and control applications, including delay, cycle timing, and intermittent timing. It features a dual LED display for clear indication of timing parameters and can handle a maximum working current of 10A and a maximum power of 1500W.
Konfiguracja i okablowanie
Proper wiring is essential for the safe and correct operation of the relay board. Refer to the wiring diagram below for connection details.
Rysunek 1: Schemat połączeń. This diagram illustrates how to connect the DC 12V power source and the load to the relay board. Ensure correct polarity for the DC 12V input and proper connection of the load to the relay output terminals.
The relay board requires a DC 12V power supply. Connect the positive (+) terminal of your 12V DC power source to the '+' terminal on the board and the negative (-) terminal to the '-' terminal. The load (e.g., a light, motor, or other device) should be connected to the relay output terminals. The relay acts as a switch, controlling the power to your load. Ensure all connections are secure before applying power.
Figure 2: Terminal Blocks. Zbliżenie view of the blue and green terminal blocks for power input and load connection.
Instrukcja obsługi
The ASHATA Digital Relay Board features a dual LED display and several buttons for configuration. Understanding these components is key to operating the device.
Rysunek 3: Układ panelu przedniego. This image highlights the LED indicator, Timing T1 display, Timing T2 display, Reset button, Set key, and adjustment buttons (+/-).
Główne funkcje:
- LED Indicator (OUT): Illuminates when the relay is active.
- Timing T1 Display: Shows the primary timing value (red display).
- Timing T2 Display: Shows the secondary timing value (blue display).
- Przycisk reset: Resets the current timing operation or settings.
- SET Key (Gear Icon): Służy do wejścia w tryb programowania i potwierdzenia ustawień.
- '+' Button (Up Arrow): Increases the timing value or navigates through options.
- '-' Button (Down Arrow): Decreases the timing value or navigates through options.
Setting Timing Parameters:
- Wejdź w tryb programowania: Naciśnij i przytrzymaj USTAWIĆ key (gear icon) for a few seconds until the display starts flashing or shows a mode selection.
- Select Time Unit: Użyj '+' or '-' buttons to cycle through time units: seconds (S), minutes (M), or hours (H). Press USTAWIĆ aby potwierdzić.
- Set T1 Value: The T1 display will flash. Use the '+' or '-' buttons to adjust the desired timing value for T1 (0-999). Press USTAWIĆ aby potwierdzić.
- Set T2 Value: If applicable for the selected function mode, the T2 display will flash. Use the '+' or '-' buttons to adjust the desired timing value for T2 (0-999). Press USTAWIĆ aby potwierdzić.
- Wybierz tryb funkcji: The display will show a function code (e.g., P-1, P-2, etc.). Use the '+' or '-' buttons to select one of the 18 available function combinations (delay, timing, cycle, intermittent timing). Refer to the product's detailed function table for specific mode descriptions. Press USTAWIĆ to confirm and exit programming mode.
Once settings are confirmed, the module will begin operation according to the selected mode and timing parameters. The LED indicator will show the relay's status.
Konserwacja
The ASHATA DC 12V Digital Relay Board is designed for low maintenance. To ensure optimal performance and longevity:
- Utrzymuj urządzenie w czystości, bez kurzu i zanieczyszczeń. Do czyszczenia używaj miękkiej, suchej ściereczki.
- Unikaj wystawiania modułu na działanie nadmiernej wilgoci lub ekstremalnych temperatur.
- Regularnie sprawdzaj połączenia przewodów, aby mieć pewność, że są bezpieczne.
- Nie próbuj otwierać casing or modify the internal components, as this may void the warranty and cause damage.
Rozwiązywanie problemów
If you encounter issues with your ASHATA Digital Relay Board, refer to the following common problems and solutions:
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Urządzenie nie włącza się. | Incorrect power connection or no power supply. | Verify DC 12V power supply is connected correctly and is active. Check polarity. |
| Przekaźnik nie aktywuje się. | Incorrect function mode selected, timing values set to zero, or load not connected properly. | Review function mode and timing settings. Ensure the load is correctly wired to the relay output. |
| Wyświetlacz jest pusty lub działa nieregularnie. | Power fluctuations or internal fault. | Disconnect and reconnect power. If the issue persists, contact customer support. |
| Nie można zmienić ustawień. | Not in programming mode. | Naciśnij i przytrzymaj USTAWIĆ key to enter programming mode. |
Specyfikacje
Below are the technical specifications for the ASHATA DC 12V Digital Relay Board:
- Model: ASHATAmei46std7w
- Wejście Voltage: Prąd stały 12 V
- Maksymalny prąd roboczy: 10A
- Maksymalna moc: 1500 W
- Zakres czasu: 0-999 seconds, 0-999 minutes, 0-999 hours (selectable)
- Tryby funkcji: 18 types (Delay, Timing, Cycle Timing, Intermittent Timing, etc.)
- Wyświetlacz: Dual LED (Red for T1, Blue for T2)
- Tworzywo: Plastikowy
- Rozmiar produktu: Około 3 x 9.7 x 5.2 cm (1.1 x 3.8 x 2.0 cala)
- ASIN: B07X5L8PPP
- Kod UPC/GTIN: 748904169309
Rysunek 4: Wymiary produktu. This image shows the approximate measurements of the relay board.
Informacje o gwarancji
ASHATA products typically come with a standard manufacturer's warranty. For specific warranty details, including duration and coverage, please refer to the documentation provided with your purchase or contact ASHATA customer support. Keep your proof of purchase for warranty claims.
Obsługa klienta
For further assistance, technical support, or inquiries regarding your ASHATA DC 12V Digital Relay Board, please contact ASHATA customer service. You can typically find contact information on the product packaging or the official ASHATA webstrona.