ELING 2-inch Digital GPS Speedometer Odometer User Manual

1. Wprowadzenie

This manual provides detailed instructions for the installation, operation, and maintenance of your ELING 2-inch Digital GPS Speedometer Odometer. This instrument is designed for various applications including RC cars, dirt bikes, vans, and marine boats, offering precise speed and odometer readings. Please read this manual thoroughly before installation and use to ensure proper function and safety.

2. Koniec produktuview

The ELING 2-inch Digital GPS Speedometer Odometer features a red backlight for clear visibility and operates on a 9-32VDC power supply, making it suitable for both 12V and 24V systems. It is designed with 100% waterproof and anti-fogging protection for durability in various environments.

Główne cechy:

• Digital display for current speed and odometer (ODO).
• Adjustable units: Kilometers per Hour (KM/H), Miles per Hour (MPH), and Knots.
• Red backlight for enhanced visibility in low light conditions.
• Szeroka objętość operacyjnatagZakres: 9-32VDC.
• Waterproof and anti-fogging design.

Rycina 2.1: Przód view of the ELING 2-inch Digital GPS Speedometer Odometer.

3. Konfiguracja i instalacja

Follow these steps carefully for proper installation of your GPS speedometer.

3.1 Montaż panelowy

1. Cut a 52mm (2 1/16") diameter hole in the desired panel location. Ensure a clearance of at least 70mm (2 3/4") behind the panel for the gauge to fit.
2. Włóż miernik do przygotowanego otworu.
3. Secure the gauge using the provided M4 nut and C-type bracket to seal it firmly in place.

Figure 3.1: Installation diagram for panel mounting.

3.2 Podłączenie anteny GPS

1. Securely fasten the GPS antenna in a flat position with the black side facing upwards. For optimal signal reception, place it outside or inside the front windscreen, ensuring a clear view nieba.
2. Connect the antenna cable to the designated socket at the back of the gauge. Do not cut the antenna cable.
3. Upon initial power-on, the GPS speedometer may take approximately 30 seconds to acquire a signal. Subsequent signal acquisition will typically take less than 3 seconds, especially under clear skies.

Figure 3.2: GPS Speedometer and antenna.

3.3 połączeń przewodów

Refer to the wiring diagram below for correct electrical connections. Ensure all connections are secure to prevent malfunctions.

• Czerwony przewód: Connect to +9-32VDC power supply.
• Niebieski przewód: Connect to Ground (-).
• Pomarańczowy przewód: Connect to Red Backlight (+).

Rysunek 3.3: Tył view with wiring harness and GPS antenna port.

4. Instrukcja obsługi

4.1 Wyświetlanie informacji

The speedometer displays the current speed and the accumulated odometer (ODO) reading. The ODO value is accumulated and does not reset when power is turned off.

4.2 Adjusting Units

To switch between speed units (KM/H, MPH, KNOTS), press the black button located on the back of the gauge. Each press will cycle through the available units. The selected unit will be saved automatically.

Figure 4.1: Location of the black button for unit adjustment.

5. Konserwacja

The ELING GPS Speedometer Odometer is designed for durability and requires minimal maintenance. To ensure longevity and clear readings:

• Regularly clean the display with a soft, damp szmatką. Unikaj środków czyszczących o działaniu ściernym i rozpuszczalników.
• Upewnij się, że wszystkie połączenia elektryczne są bezpieczne i nie ulegają korozji.
• Periodically check the GPS antenna placement to ensure it maintains a clear view nieba w celu optymalnego odbioru sygnału.

6. Rozwiązywanie Problemów

If you encounter issues with your GPS speedometer, refer to the following common problems and solutions:

Kody błędów:

• E01: GPS cannot search for a GPS signal when powered on.
• E02: GPS signal lost during operation.
• E03: The internal circuit of the instrument is faulty.

Ogólne wskazówki dotyczące rozwiązywania problemów:

• Brak wyświetlacza/zasilania: Check all wiring connections, especially the power (red) and ground (blue) wires, to ensure they are secure and receiving the correct voltage (9-32 V prądu stałego).
• No GPS Signal (E01/E02): Verify that the GPS antenna has a clear, unobstructed view of the sky. Ensure the antenna cable is securely connected to the gauge and is not damaged. Move the vehicle to an open area if indoors or under heavy cover.
• Nieprawidłowe odczyty: Ensure the correct unit (KM/H, MPH, KNOTS) is selected. If readings are consistently inaccurate, recheck the GPS antenna placement.
• Problemy z wyświetlaniem: If the display is dim or flickering, check the power supply. If an E03 error occurs, the internal circuit may be faulty, and professional assistance or replacement may be required.

7. Specyfikacje

8. Gwarancja i wsparcie

For warranty information or technical support, please refer to the documentation included with your product or contact ELING customer service directly. Ensure you have your product model number and purchase details available when seeking support.

You can visit the official ELING store for more information: ELING Store on Amazon