1. Koniec produktuview
The Springfield Speaker Pro-Grade Black Rubberized Speaker Repair Adhesive Glue is a professional-grade, hexane-based rubberized adhesive. It is specifically formulated to create a permanent, flexible bond for various speaker repair applications. This adhesive is designed to dry black, blending seamlessly with many speaker components.
Image 1.1: A 1/2 oz bottle of Springfield Speaker Pro-Grade Black Rubberized Speaker Repair Adhesive Glue.
Główne cechy:
- Professional-grade hexane-based rubberized adhesive.
- Forms a permanent, flexible bond.
- Dries black for a discreet repair.
- Available in various sizes (1/2 oz, 1 oz, 2 oz, 4 oz, 8 oz, 16 oz).
- Includes a Yorker lid for precise application.
Przeznaczenie:
This adhesive is suitable for:
- Attaching cones and surrounds to speaker frames.
- Replacing or attaching foam surrounds.
- Attaching dust caps.
- Attaching gaskets.
- Repairing holes in speaker cones.
Ważna uwaga: This adhesive is NIE for attaching voice coils.
2. Informacje dotyczące bezpieczeństwa
This product contains hexane and is flammable. Please observe the following safety precautions:
- Wentylacja: Stosować w dobrze wentylowanym pomieszczeniu, aby uniknąć wdychania oparów.
- Łatwopalność: Keep away from heat, sparks, open flames, and other ignition sources. Do not smoke while using this product.
- Kontakt ze skórą: Avoid prolonged skin contact. If contact occurs, wash thoroughly with soap and water.
- Kontakt wzrokowy: W przypadku dostania się preparatu do oczu, należy natychmiast przemywać je dużą ilością wody przez co najmniej 15 minut i zasięgnąć porady lekarza.
- Przyjmowanie pokarmu: Nie połykać. W razie połknięcia nie wywoływać wymiotów. Natychmiast zwrócić się o pomoc lekarską.
- Składowanie: Store in a cool, dry place, away from direct sunlight and out of reach of children and pets. Keep container tightly closed when not in use.
3. Konfiguracja i przygotowanie
- Zbierz narzędzia: Ensure you have all necessary tools for your speaker repair, such as a utility knife, cleaning supplies, and any replacement parts (e.g., new foam surrounds, dust caps).
- Czyszczenie powierzchni: Thoroughly clean all surfaces where the adhesive will be applied. Remove any old glue, debris, dust, or loose material. The surfaces must be dry and free of grease or oil for optimal adhesion.
- Disassemble Speaker (if necessary): Carefully disassemble the speaker components as required for the repair. For surround replacement, this may involve carefully removing the old surround and potentially the dust cap to access the voice coil gap for shimming.
- Shim Voice Coil (if necessary): If replacing surrounds, it is crucial to ensure the voice coil remains centered. Insert shims (e.g., 3x5 cards) evenly into the voice coil gap until the cone/voice coil assembly is stiff and cannot move freely. This prevents the voice coil from rubbing against the pole piece during the gluing process.
- Wentylacja: Ensure your workspace is well-ventilated before opening the adhesive bottle.
4. Operating Instructions: Application Guide
Follow these steps for effective application of the speaker repair adhesive:
- Prepare the Adhesive: Shake the bottle gently before use. Twist open the Yorker lid for precise control over the adhesive flow.
- Apply First Layer: Apply a thin, even layer of adhesive to one of the surfaces to be joined (e.g., the speaker frame or the new surround's inner edge). For surround attachment, apply glue around the cone where the surround will sit.
- Allow to Tack: Wait approximately 5 minutes for the adhesive to become tacky. This allows some solvents to evaporate, improving bond strength.
- Apply Second Layer (Optional, for stronger bond): For critical repairs or larger surfaces, a second, slightly thicker layer can be applied after the first layer has become tacky.
- Połącz powierzchnie: Carefully align and press the components together. For surrounds, gently pull the cone up to meet the surround, ensuring good contact. Apply even pressure around the entire joint.
- Bezpieczna pozycja: If necessary, use clamps or weights to hold the components in place while the adhesive sets. Ensure the voice coil remains centered if shims were used.
- Czas utwardzania: The adhesive will tack in approximately 5 minutes, but a full cure requires 24 godziny. Do not apply stress or use the speaker before the full curing time has elapsed to ensure a strong, permanent bond.
- Remove Shims (if used): After the adhesive has fully cured (24 hours), carefully remove any shims from the voice coil gap.
- Ponowny montaż: Reassemble any other speaker components that were removed.
Image 4.1: A hand applying the black rubberized adhesive to the edge of a speaker cone, preparing it for surround attachment.
5. Konserwacja
Przechowywanie kleju:
- Always replace the Yorker lid tightly after each use to prevent the adhesive from drying out.
- Store the bottle upright in a cool, dry place, away from direct sunlight and extreme temperatures.
- Ensure it is stored out of reach of children and pets.
Czyszczenie:
- Clean any excess wet adhesive immediately with a suitable solvent (e.g., mineral spirits or naphtha) on a cloth. Test solvent on an inconspicuous area first.
- Once cured, the adhesive is difficult to remove without damaging the speaker components.
6. Rozwiązywanie Problemów
| Problem | Możliwa przyczyna | Rozwiązanie |
|---|---|---|
| Adhesive not bonding properly. | Surfaces were not clean or dry; insufficient adhesive applied; not enough curing time; improper alignment. | Ensure surfaces are thoroughly cleaned and dry. Apply an adequate amount of adhesive. Allow full 24-hour cure time without disturbance. Re-evaluate alignment during application. |
| Adhesive dries too quickly. | High ambient temperature; low humidity; excessive airflow. | Work in a cooler environment if possible. Reduce direct airflow over the adhesive during application. Work quickly. |
| Adhesive dries too slowly. | Low ambient temperature; high humidity; excessive adhesive applied. | Ensure adequate ventilation. Work in a warmer, less humid environment. Apply thinner, even coats. Extend curing time if necessary. |
| Voice coil rubbing after repair. | Voice coil not properly centered during surround attachment; shims removed too early. | This often requires re-doing the repair. Ensure shims are used correctly and remain in place until the adhesive is fully cured (24 hours). |
7. Specyfikacje
Image 7.1: A range of Springfield Speaker Pro-Grade Black Rubberized Speaker Repair Adhesive Glue bottles in different sizes.
| Marka | Mówca ze Springfield |
| Numer modelu | 8541762759 |
| Konkretne zastosowania produktu | Speaker Repair |
| Tworzywo | Rubber-Based |
| Formularz przedmiotu | Żel |
| Funkcja specjalna | Gumowane |
| Kolor | Czarny |
| Ilość w opakowaniu przedmiotu | 1 |
| Informacje o pakiecie | Butelka |
| Objętość przedmiotu | 15 mililitrów (0.5 uncji) |
| Lepkość | Wysoka lepkość |
| Czas całkowitego utwardzania | 24 godzin |
| Poziom wodoodporności | Nie jest wodoodporny |
| Wymiary produktu | 3 x 1 x 1 cala |
| Waga przedmiotu | 0.32 uncji |
| UPC | 810694027142 |
| Pierwsza dostępna data | 6 czerwca 2018 r. |
8. Gwarancja i wsparcie
Specific warranty information for this product is not provided in the available documentation. For product support, technical assistance, or inquiries regarding your Springfield Speaker adhesive, please contact Springfield Speaker directly through their official channels or visit their brand store on Amazon:
Springfield Speaker Amazon Store
Always refer to the product packaging for the most current contact and support information.