Teknetics T2+ Metal Detector Bundle User Manual

Ważne informacje dotyczące bezpieczeństwa

• Always operate the metal detector responsibly and in accordance with local laws and regulations.
• Avoid searching in areas where unexploded ordnance or dangerous materials may be present.
• Podczas kopania należy zachować ostrożność, aby nie uszkodzić podziemnych instalacji lub zabytków.
• Trzymaj baterie poza zasięgiem dzieci. Zużyte baterie utylizuj prawidłowo.
• The Digger knife is sharp. Handle with care and store safely.

Produkt ponadview

The Teknetics T2+ Metal Detector Bundle is a high-performance, multi-purpose professional-grade metal detecting system designed for various treasure hunting and relic recovery applications. This bundle includes the T2+ metal detector, a Tek-Point waterproof pinpointer, and a Digger 12-inch carbon steel digging knife.

Figure 1: Teknetics T2+ Metal Detector Bundle. This image displays the complete bundle, including the T2+ metal detector, Tek-Point pinpointer, and Digger knife.

Zawartość zestawu:

• Teknetics T2+ Metal Detector
• Tek-Point Waterproof Pinpointer
• Digger 12-inch Carbon Steel Digging Knife
• Free Refurbishment Certificate with Transferable and Extended Warranty

Konfiguracja i montaż

1. Assembling the T2+ Metal Detector

1. Podłącz cewkę poszukiwawczą: Secure the 11-inch Open-Frame Bi-Axial Searchcoil to the lower stem using the provided bolt and washers. Ensure it is snug but do not overtighten.
2. Połącz łodygi: Insert the lower stem into the middle stem, and then the middle stem into the upper stem (control housing). Adjust the length to a comfortable operating position and secure with the locking collars.
3. Zamontuj obudowę sterującą: Slide the control housing onto the upper stem.
4. Owiń kabel: Carefully wrap the searchcoil cable around the stem, leaving enough slack near the searchcoil for movement. Plug the cable connector into the receptacle on the control housing. Ensure the connection is secure.
5. Zainstaluj baterie: Open the battery compartment on the control housing. Insert four (4) AA batteries, observing the correct polarity. Close the compartment securely.

2. Tek-Point Pinpointer Setup

Figure 2: Tek-Point Waterproof Pinpointer. This image shows the Tek-Point pinpointer, a handheld device used for precise target location.

The Tek-Point pinpointer requires a 9V battery (not included). Open the battery cap at the rear of the unit, insert the 9V battery with correct polarity, and securely close the cap. The pinpointer is ready for use once the battery is installed.

3. Digger Knife

Figure 3: Digger 12-inch Carbon Steel Digging Knife. This image displays the Digger knife with its sheath, designed for excavating targets.

The Digger knife comes with a protective sheath. Always store the knife in its sheath when not in use to prevent injury and protect the blade.

Instrukcja obsługi

1. Teknetics T2+ Metal Detector Operation

• Włączanie/wyłączanie: Press and hold the power button to turn the detector on or off.
• Wyświetlacz LCD: The large, easy-to-read LCD displays target identification (0-99), depth, mineralization bar graph, and current settings.
• Częstotliwość pracy: The T2+ operates at a 13 kHz frequency, suitable for a wide range of targets and ground conditions.
• Discrimination Modes: Utilize the Double Filter Discrimination Modes to filter out unwanted metals (e.g., iron) and focus on desirable targets. Refer to the on-screen prompts for adjusting discrimination levels.
• Tryb wzmocnienia: Activate Boost Mode for enhanced depth detection, particularly useful for deeply buried targets.
• Ground Balance (FASTGRAB): The Trigger-Actuated FASTGRAB feature allows for quick and accurate ground balancing, essential for stable operation in varying soil conditions. Squeeze the trigger and pump the searchcoil to perform an automatic ground balance.
• Searchcoil Usage: The Waterproof 11-inch Open-Frame Bi-Axial Searchcoil can be submerged in water. Swing the searchcoil slowly and steadily over the search area, keeping it parallel to the ground.

2. Tek-Point Pinpointer Operation

• Włączanie/wyłączanie: Press the power button to turn the pinpointer on. It will emit a short tone or vibration. Press again to turn off.
• Wybór trybu: Cycle through the three settings (vibrate only, audible only, vibrate/audible) by pressing the mode button.
• Regulacja czułości: Adjust the sensitivity (low, medium, high) within each mode to fine-tune detection. Higher sensitivity detects smaller or deeper targets but may be more susceptible to interference.
• Wodoodporna konstrukcja: The Tek-Point is waterproof, allowing for use in wet conditions or shallow water. Ensure the battery cap is securely fastened before submersion.

3. Digger Knife Usage

Use the Digger knife to carefully excavate targets located by the metal detector and pinpointer. Its carbon steel construction and serrated edge are designed for efficient digging in various soil types. Always dig away from yourself and others, and be mindful of the surrounding environment.

Konserwacja

• Czyszczenie: After each use, wipe down the metal detector, pinpointer, and Digger knife with a damp cloth to remove dirt and debris. For the T2+ control housing, use a dry cloth. Avoid harsh chemicals.
• Pielęgnacja baterii: Remove batteries from the T2+ and Tek-Point if storing the devices for extended periods to prevent leakage. Replace batteries when the low battery indicator appears or performance degrades.
• Składowanie: Store all components in a clean, dry place, away from extreme temperatures and direct sunlight. Ensure the Digger knife is sheathed.
• Searchcoil Protection: While the searchcoil is waterproof, avoid unnecessary impacts or abrasions. Consider using a searchcoil cover (sold separately) for added protection.

Rozwiązywanie problemów

Specyfikacje

Gwarancja i wsparcie

The Teknetics T2+ Bundle includes a free refurbishment certificate with a transferable and extended warranty. For specific details regarding warranty coverage, duration, and claims, please refer to the documentation provided with your purchase or visit the official Teknetics website. For technical support or service inquiries, please contact Teknetics customer service.