Brondell Swash SE600 Elongated Bidet Toilet Seat User Manual

Wstęp

This manual provides detailed instructions for the installation, operation, and maintenance of your Brondell Swash SE600 Elongated Bidet Toilet Seat. This electronic bidet seat is designed to enhance personal hygiene with features such as a heated seat, warm air dryer, oscillating stainless-steel nozzle for both rear and front wash, gentle massage pulse, deodorizer, power-saving eco-mode, and an ambient nightlight.

Informacje dotyczące bezpieczeństwa

Please read all instructions carefully before installation and use. Keep this manual for future reference. Ensure the bidet seat is connected to a properly grounded GFCI outlet. Do not immerse the unit in water. Disconnect power before cleaning or servicing. Avoid using abrasive cleaners on the bidet seat. This product is intended for household use only.

Zawartość opakowania

Przed rozpoczęciem instalacji sprawdź, czy wszystkie komponenty są obecne:

• Brondell Swash SE600 Bidet Toilet Seat (Elongated)
• Wireless Remote Control (with 2 AAA batteries)
• Płyta montażowa i śruby
• T-Valve (for water connection)
• Wąż do bidetu
• Washers and Nuts
• Instrukcja obsługi (ten dokument)

Konfiguracja i instalacja

Follow these steps for proper installation of your Brondell Swash SE600 bidet toilet seat. No special tools are typically required, and installation can be completed in under an hour.

1. Measure Your Toilet for Proper Fit

Before installation, ensure your toilet is compatible with an elongated bidet seat. Measure the distance from the bolt holes to the front of the toilet bowl (Dimension A) and the distance from the center of the bolt holes to the toilet tank (Dimension B). Also, measure the distance between the bolt holes (Dimension C).

Image: Diagram illustrating how to measure your toilet for proper bidet seat fit. It shows three key measurements: A (from bolt holes to front of bowl), B (from bolt holes to tank), and C (distance between bolt holes). For elongated seats, Dimension A should be 18"-19.5".

Image: Visual comparison of round (16.5") and elongated (18.5") toilet seat dimensions, highlighting the difference in length.

2. Prepare Your Toilet

1. Remove your existing toilet seat and thoroughly clean the toilet bowl and surrounding area.
2. Turn off the water supply at the shut-off valve located at the wall behind your toilet.
3. Flush the toilet to drain the tank completely. Hold down the flush handle until all water is drained.
4. Unscrew the flexible water supply line from the fill valve at the bottom of the toilet tank. Have a small bucket or towel ready to catch any residual water.

3. Install the T-Valve

1. Connect the provided T-valve to the fill valve under the toilet tank. Ensure the rubber gasket is properly seated to prevent leaks.
2. Reconnect the flexible water supply line to the bottom of the T-valve.

4. Zainstaluj płytę montażową

1. Place the mounting plate over the bolt holes on the toilet, ensuring the arrow on the plate points towards the toilet bowl.
2. Slide the mounting bolts through the holes in the toilet and secure them with the provided washers and nuts from underneath. Leave the bolts loose enough to allow for minor adjustments later.

5. Attach the Bidet Seat

1. Place the Swash bidet seat flat onto the toilet, in front of the mounting plate.
2. Slide the Swash seat towards the tank onto the mounting plate until it clicks securely into place.
3. Adjust the position of the seat by sliding it forward or backward for the best fit, then tighten the nuts under the toilet to secure it.

6. Connect Water and Power

1. Connect the elbow side of the bidet hose to the Swash's water inlet on the side of the seat.
2. Connect the open end of the bidet hose to the T-valve.
3. Turn on the water supply at the shut-off valve and check for any leaks.
4. If no leaks are present, plug the Swash into the nearest Ground Fault Circuit Interrupter (GFCI) outlet. The bidet should power on, illuminating the power indicator light. If not, press any button on the seat's control panel.

Instrukcja wideo instalacji

Instrukcja obsługi

The Brondell Swash SE600 features a wireless remote control for easy operation. Ensure the remote has batteries installed and is functioning correctly.

Pilot zdalnego sterowaniaview

Image: The wireless remote control for the Brondell Swash SE600, displaying various buttons for wash functions (Rear, Front, Dry), settings adjustments (Nozzle Position, Water Pressure/Dry Temp, Water Temp, Seat Temp), and advanced features (Massage, Move, Auto Mode, Deodorize).

Basic Wash Functions

1. Mycie Tyłu: Press the "Rear" button for a posterior wash.
2. Mycie przodu: Press the "Front" button for a feminine wash.
3. Zatrzymać: Press the "Stop" button to end any active wash or dry cycle.

Dostosowywanie ustawień

• Temperatura wody: Use the "Water Temp" button to cycle through available water temperature settings (e.g., low, medium, high, off). Allow 3-4 minutes for the water to heat to your desired temperature.
• Ciśnienie wody: Use the "+" and "-" buttons under "Water Pressure / Dry Temp" to adjust the water spray intensity.
• Pozycja dyszy: Use the "Nozzle Position" up and down arrows to adjust the nozzle's projection for optimal cleaning.
• Temperatura siedziska: Use the "Seat Temp" button to adjust the heated seat temperature.

Obraz: Zbliżenie view of the bidet's self-cleaning stainless steel nozzle, illustrating its five adjustable positions and aerated water spray for effective cleaning.

Zaawansowane funkcje

• Suszarka na ciepłe powietrze: After a wash cycle, press the "Dry" button to activate the warm air dryer. Adjust the dry air temperature using the "+" and "-" buttons under "Water Pressure / Dry Temp".
• Masaż: Press the "Massage" button for a pulsating wash spray.
• Przenosić: Press the "Move" button to activate an oscillating nozzle movement for a wider cleaning area.
• Tryb automatyczny: Press "Auto Mode" for a complete wash and dry cycle.
• Środek dezodoryzujący: The built-in deodorizer automatically activates to neutralize odors.
• Lampka nocna: The ambient nightlight provides soft illumination for nighttime use.
• Tryb ekologiczny: Activate "Eco Mode" to conserve energy by lowering the seat and water heating temperatures when not in use.

Konserwacja

Regular cleaning and maintenance will ensure the longevity and optimal performance of your Brondell Swash SE600.

• Czyszczenie zewnętrzne: Przetrzyj zewnętrzne powierzchnie miękką, damp cloth and a mild, non-abrasive cleaner. Avoid harsh chemicals or abrasive pads.
• Czyszczenie dysz: The stainless-steel nozzle is self-cleaning. For additional cleaning, you can manually extend the nozzle (refer to the full owner's manual for specific instructions) and gently clean it with a soft brush.
• Konserwacja filtra: Periodically check the water inlet filter for sediment buildup. Clean if necessary to maintain water flow.
• Przechowywanie długoterminowe: If storing the bidet seat for an extended period, drain all water from the unit and disconnect it from power.

Rozwiązywanie problemów

For further troubleshooting or issues not listed, please refer to the comprehensive owner's manual or contact Brondell customer support.

Specyfikacje

• Model: SE600
• Typ: Deska sedesowa bidetowa wydłużona
• Kolor: Biały
• Tworzywo: Plastikowy
• Wymiary produktu: 20.7" dł. x 14.9" szer.
• Waga przedmiotu: 9.7 funtów
• Tomtage: 120 wolty
• Cotage: 660.00 watów
• Baterie: 2 baterie AAA (w zestawie do pilota)
• Cechy: Heated Seat, Warm Air Dryer, Oscillating Stainless-Steel Nozzle, Rear/Front Wash, Massage, Move, Auto Mode, Deodorizer, Ambient Nightlight, Eco Mode.

Gwarancja i wsparcie

For warranty information, product registration, or technical support, please visit the official Brondell webOdwiedź witrynę lub skontaktuj się z działem obsługi klienta. Zachowaj paragon jako dowód zakupu na wypadek reklamacji.

Brondell Customer Support: www.brondell.com/support