Cukierek 92130871

Candy 92130871 Washing Machine Replacement Belt Instruction Manual

Model: 92130871

1. Wprowadzenie

This instruction manual provides essential information for the proper installation, maintenance, and troubleshooting of the Candy 92130871 washing machine replacement belt. Please read this manual thoroughly before attempting any installation or repair to ensure safe and effective operation.

2. Informacje dotyczące bezpieczeństwa

  • Always disconnect the washing machine from the power supply before attempting any installation, maintenance, or repair work. Failure to do so can result in electric shock or serious injury.
  • Aby zapobiec obrażeniom, należy nosić odpowiedni sprzęt ochrony osobistej, np. rękawice.
  • Jeśli masz jakiekolwiek wątpliwości, skonsultuj się z wykwalifikowanym technikiem.
  • Podczas naprawy należy trzymać dzieci i zwierzęta domowe z dala od urządzenia.
  • Upewnij się, że wszystkie narzędzia są w dobrym stanie i prawidłowo używane.

3. Koniec produktuview

The Candy 92130871 is an authentic replacement drive belt designed for various Candy washing machine models. This belt is crucial for transmitting power from the motor to the drum, enabling the washing machine to operate correctly.

Candy 92130871 Washing Machine Replacement Belt

Image 1: The Candy 92130871 washing machine replacement belt. This image shows the black rubber belt, typically ribbed on one side for grip.

4. Zgodność

This replacement belt (Manufacturer Code: 92130871) is compatible with a wide range of Candy washing machine models. Please verify your washing machine's model number against the list below to ensure proper fitment.

Kompatybilne modele obejmują:

  • CANDY AC16, ACTIVA50, ACTIVA51, ACTIVA60, ACTIVA61, ACTIVA64SLIM, ACTIVA66SL, ACTIVA6CI
  • ALISE060, ALISE065, ALISE066, ALISE'160XT, ALISE190X, ALISE6190X0, ALISE'.610B, ALISE'65 ARG, ALISE'650, ALISE'696
  • AQUAV.6, AQUAVIVA60, AQUAVIVA63, AQUAVIVA650, AQUAVIVA66
  • C36ZXT, C532, C535T, C536T, C55XT (I), C564XT plata, C577T, C588XT, C58XT (I), C6077T, XT AQUAM, CM.608XT (I)
  • C616XT (I), C625XT, C634XT, C634XT (CE), C634XT (NORD), C636XT, C647XT (I), C657XT (I)
  • CB52T, CB52TCKD, CB53XTR, CB612XT, CB613TR, CB623XTTR HC, CB62T, CB62TR, CB633XTR, CB634XT, CB63TES, CB63TR, CB63TRCKD, CB63XTR
  • CE520T, CE530, CE615, CE621T, CE623R, CE625TR, CE629T, CE637XT, CE650TR
  • CG5444T, CG5544T, CG623T, CG644.3T, CG644T, CG654XT, CGAQ665XT
  • CH630, CHIARA51XT, CHIARA540XTR, CHIARA552TR, CHIARA55XTR, CHIARA5XT, CHIARA5XTV, CHIARA642XTR, CHIARA65XTR, CHIARA65XT, CHIARA65XTV, CHIARA65XTR, CHIARA65X2XTR, CHIARA6XT
  • CI50XTR, CI537T, CI57TR, CI589XT, CI60XTR, CI60XTR H/C, CI620TP, CI622T, CI624T, CI626XT, CI627T, CI637T, CI648XT, CI658XT
  • CJ6514, CJ543T, CJ613XT, CJ643T, CJA52T
  • CL66XT, CN50T, CN50T-04S, CN60T, CN63T, CN63T CI, CN63TCKD, CN63TRU-03S
  • IPC 610, CR61, CS47XT (I), CSB640XTR, CSE640XTR, CSE615XT, CM.SE635XT, CSG624T, CSI615T, CSI635XTR, CSI635XTRSY, CSN62T, CSN62T-03S
  • EXCL.S641XTR, EXCLUS.60, EXCLUS.6000, EXCLUS540XTR, EXCLUS65XTR
  • HOL165XTR, HOL62, VACANZAS 6, HOLIDAY161, HOLIDAY60, HOLIDAY603, HOLIDAY61
  • ICL60T, LADYC.623CKD, SEL.S643XTR, SELEC 0.631 XTR, SELECTA600, SELECTA60X, SELECTA61XXTR
  • SL5000EXC, SL50EXCLUS., SLIM644AQUAV, SLIMMY508XT, SLIMMY634XT, SLIMMY655XT, SLIMMY6AQUAV, SLIMMYCB62XT, WM601.

5. Instalacja (konfiguracja)

Replacing a washing machine drive belt requires careful attention. Follow these general steps. Specific machine designs may vary, so refer to your washing machine's primary service manual if available.

  1. Przygotowanie:
    • Odłącz pralkę od zasilania sieciowego.
    • Zamknąć dopływ wody do urządzenia.
    • Pull the washing machine away from the wall to access the rear panel.
  2. Dostęp do Pasa:
    • Locate and remove the screws securing the rear access panel of the washing machine.
    • Carefully remove the panel to expose the motor, drum pulley, and the old belt (if still present).
  3. Zdejmij stary pasek:
    • If the old belt is still partially attached, carefully pry it off the motor pulley and then the larger drum pulley. Note its orientation.
  4. Zamontuj nowy pasek:
    • First, loop the new Candy 92130871 belt around the smaller motor pulley.
    • Next, partially loop the belt around the larger drum pulley.
    • While holding the belt firmly on the motor pulley and partially on the drum pulley, slowly rotate the drum pulley by hand. The belt should gradually roll onto the drum pulley until it is fully seated. Ensure the ribbed side of the belt (if applicable) faces the pulleys correctly.
    • Check that the belt is centered on both pulleys and has proper tension. It should be snug but allow for a small amount of flex.
  5. Ponowny montaż:
    • Replace the rear access panel and secure it with the screws.
    • Push the washing machine back into its position.
    • Reconnect the power supply and water supply.
  6. Test:
    • Run a short, empty wash cycle to ensure the belt operates smoothly and quietly.

6. Konserwacja

Regular inspection of the drive belt can help prevent future issues and extend the life of your washing machine.

  • Przeglądy okresowe: Co 1–2 lata lub jeśli zauważysz nietypowe dźwięki lub problemy z działaniem paska, sprawdź, czy nie ma na nim śladów zużycia, pęknięć, przetarć lub rozciągnięcia.
  • Prawidłowe napięcie: Ensure the belt maintains proper tension. A loose belt can slip, causing the drum to not spin or spin intermittently. An overly tight belt can put undue stress on the motor and drum bearings.
  • Czystość: Keep the area around the motor and pulleys free from lint, debris, and moisture, which can affect belt performance and lifespan.

7. Rozwiązywanie Problemów

ProblemMożliwa przyczynaRozwiązanie
Bęben nie obraca się lub obraca się powoliBroken, stretched, or slipped drive belt.Inspect the belt. Replace if broken or severely worn. Re-seat if slipped.
Loud squealing or grinding noise during spin cycleWorn or misaligned drive belt.Check belt for wear and proper alignment on pulleys. Replace if worn.
Zapach spaleniznyBelt slipping due to improper tension or excessive load.Check belt tension and ensure it's not overloaded. Replace if damaged from slipping.

If troubleshooting steps do not resolve the issue, it is recommended to contact a qualified appliance technician.

8. Specyfikacje

  • Marka: Słodycze
  • Numer modelu: 92130871
  • Typ produktu: Washing Machine Replacement Belt
  • Zgodne urządzenia: Pralka
  • Wymiary opakowania: 30 x 20 x 3 cm (w przybliżeniu)
  • Waga produktu: 100 g (w przybliżeniu)

9. Gwarancja i wsparcie

For information regarding warranty coverage, technical support, or to purchase additional parts, please refer to the official Candy webOdwiedź stronę internetową lub skontaktuj się z działem obsługi klienta. Zachowaj paragon jako dowód zakupu.

Oficjalne słodycze Webstrona: www.candy-group.com

© 2023 Candy. Wszelkie prawa zastrzeżone. Niniejsza instrukcja służy wyłącznie celom informacyjnym.