Dawson Tools DSM170 Multifunction Moisture Meter User Manual

1. Wprowadzenie

The Dawson Tools DSM170 is a versatile multifunction meter designed to accurately measure moisture content in various materials, ambient temperature, and relative humidity. This device is an essential tool for professionals and DIY enthusiasts requiring precise environmental and material condition assessments. Please read this manual thoroughly before operating the device to ensure safe and correct usage.

2. Informacje dotyczące bezpieczeństwa

Always observe the following safety precautions to prevent injury and avoid damage to the meter:

• Nie próbuj otwierać licznika casing. Wewnątrz nie ma żadnych części nadających się do samodzielnej naprawy przez użytkownika.
• Keep the meter away from water and other liquids.
• Avoid using the meter in environments with high humidity or extreme temperatures beyond its specified operating range.
• Do not insert the measurement pins into electrical outlets or live circuits.
• Handle the measurement pins with care as they are sharp. Keep out of reach of children.
• Aby zapobiec wyciekowi elektrolitu, wyjmij baterie, jeśli miernik nie będzie używany przez dłuższy czas.

3. Koniec produktuview

Familiarize yourself with the components of your DSM170 meter:

Rysunek 1: Przód view of the Dawson Tools DSM170 Multifunction Moisture Meter. Shows the LCD display, function buttons, and measurement pins at the top.

• Measurement Pins: Used for contact moisture measurement in materials.
• Wyświetlacz LCD: Shows measurement readings, units, and battery status.
• Przycisk zasilania: Włącza lub wyłącza urządzenie.
• Przycisk trybu: Cycles through measurement modes (e.g., moisture, temperature, humidity).
• Hold/MAX/MIN Button: Freezes the current reading or displays maximum/minimum values.
• Przycisk jednostki: Changes temperature units (Celsius/Fahrenheit).
• Komora baterii: Located at the rear, holds 2 AAA batteries.

4. Konfiguracja

4.1. Instalacja baterii

1. Znajdź pokrywę komory baterii znajdującą się z tyłu miernika.
2. Slide the cover open or unscrew it if applicable.
3. Insert two (2) 1.5V AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
4. Dokładnie załóż pokrywę komory baterii.

4.2. Pierwsze włączenie zasilania

Naciśnij Moc button to turn on the meter. The LCD display will illuminate and show the default measurement mode.

5. Instrukcja obsługi

5.1. Włączanie/wyłączanie zasilania

• Aby włączyć: Naciśnij Moc przycisk.
• Aby wyłączyć: Naciśnij i przytrzymaj Moc button for approximately 2 seconds. The meter features an auto-power-off function to conserve battery life if inactive for a set period.

5.2. Wybór trybów pomiaru

Naciśnij Tryb button to cycle through the available measurement functions:

• Pomiar wilgotności: For wood and building materials. The display will show a percentagmi (%).
• Temperatura otoczenia: Wyświetla temperaturę w stopniach Celsjusza lub Fahrenheita.
• Wilgotność względna: Displays humidity in percentagi (RH%).

5.3. Moisture Measurement (Pin-Type)

1. Ensure the meter is in moisture measurement mode.
2. Carefully push the measurement pins into the material to be tested. Ensure both pins penetrate the surface adequately for accurate contact.
3. Odczytaj zawartość wilgoci w procentachtage directly from the LCD display.
4. Remove the pins from the material after measurement.

Note: The measurement depth for moisture is approximately 0 to 50 mm.

5.4. Pomiar temperatury i wilgotności

1. Select the desired mode (Temperature or Humidity) using the Tryb przycisk.
2. Hold the meter in the environment you wish to measure. Allow a few moments for the readings to stabilize.
3. Read the ambient temperature or relative humidity from the display.

5.5. Funkcja zatrzymania danych

Naciśnij Hold/MAX/MIN button briefly to freeze the current reading on the display. Press it again to release the hold function and resume live measurements.

5.6. Funkcja MAX/MIN

While in a measurement mode, press and hold the Hold/MAX/MIN button for approximately 2 seconds to activate the MAX/MIN recording function. The display will show the maximum recorded value. Press again to show the minimum value. Press and hold again to exit this mode.

5.7. Unit Selection (Temperature)

When in temperature measurement mode, press the Jednostka aby przełączać pomiędzy stopniami Celsjusza (°C) i Fahrenheita (°F).

6. Konserwacja

6.1. Czyszczenie

Wytrzyj licznikasing z miękkim, damp cloth. Do not use abrasive cleaners or solvents. Ensure the measurement pins are clean and free of debris after each use.

6.2. Wymiana baterii

When the low battery indicator appears on the display, replace the batteries as described in Section 4.1. Promptly replace depleted batteries to ensure accurate readings and prevent potential leakage.

6.3. Przechowywanie

Store the meter in a cool, dry place, away from direct sunlight and extreme temperatures. If storing for an extended period, remove the batteries.

7. Rozwiązywanie Problemów

8. Specyfikacje

9. Gwarancja i wsparcie

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your local Dawson Tools distributor. Keep your purchase receipt as proof of purchase.