Axxess Metra AX-ADCT2 80W Differential Converter Instruction Manual

1. Wprowadzenie

The Axxess Metra AX-ADCT2 is a 2-channel differential converter designed to facilitate the integration of aftermarket audio components into a vehicle's factory sound system. This device allows for the connection of an aftermarket head unit to a factory amplifier or the addition of an aftermarket amplifier to a factory system, converting high-level speaker signals to low-level RCA outputs.

Główne cechy:

• 2-channel input for speaker-level signals
• 80-watt maximum input handling
• 6:1 step-down ratio with variable output adjustment
• Separate level adjustment for each channel (Left and Right)
• Gold-flashed RCA outputs for optimal signal transfer

Image 1.1: Axxess Metra AX-ADCT2 Differential Converter unit. This image shows the compact black housing of the converter with input and output connections clearly visible.

2. Informacje dotyczące bezpieczeństwa

Podczas instalacji i obsługi należy zawsze przestrzegać następujących środków ostrożności:

• Disconnect the vehicle's battery negative terminal before beginning any electrical installation to prevent short circuits and damage.
• Ensure all wiring connections are secure and properly insulated to prevent electrical shorts.
• Do not exceed the maximum input wattage of 80 watts to avoid damaging the converter.
• Mount the converter in a location free from excessive heat, moisture, and vibration.
• Jeśli masz jakiekolwiek wątpliwości co do któregokolwiek etapu procesu instalacji, skonsultuj się z profesjonalnym instalatorem sprzętu car audio.

3. Zawartość opakowania

Sprawdź, czy w opakowaniu znajdują się wszystkie elementy:

• Axxess 2 Channel Differential Converter (AX-ADCT2)

4. Konfiguracja i instalacja

The AX-ADCT2 converter allows you to add an aftermarket amplifier to a factory radio or integrate an aftermarket radio with a factory amplifier. Aby poprawnie zainstalować, wykonaj następujące kroki:

Schemat połączeń powyżejview:

Image 4.1: Axxess Metra AX-ADCT2 with included wiring harness. This image displays the converter unit alongside its multi-colored wiring harness, illustrating the connections for power, ground, remote, and speaker inputs.

Kroki instalacji:

1. Identyfikacja przewodów głośnikowych: Locate the factory speaker wires from the head unit or factory amplifier that you intend to use as the input for the AX-ADCT2. Typically, these are the rear speaker wires for subwoofer applications or front speaker wires for full-range amplifikacja.
2. Connect High-Level Input: Connect the factory speaker wires to the corresponding high-level input terminals on the AX-ADCT2. Ensure correct polarity (positive to positive, negative to negative) for each channel (Left and Right). The AX-ADCT2 features a 'Hi-IN' input section with 'L' and 'R' terminals.
3. Połączenia zasilania i uziemienia:
   • Połącz Grunt wire (usually black) from the AX-ADCT2 harness to a clean, unpainted metal surface on the vehicle chassis.
   • Połącz 12V Constant Power wire (usually yellow) from the AX-ADCT2 harness to a constant 12V power source.
   • Połącz Zdalne włączanie wire (usually blue) from the AX-ADCT2 harness to the remote turn-on output of your aftermarket head unit or to a switched 12V source that turns on with the ignition. This wire will provide the remote turn-on signal for your aftermarket ampliyfikator.
4. Podłącz wyjścia RCA: Connect RCA cables from the 'OUTPUT' jacks on the AX-ADCT2 to the RCA input jacks on your aftermarket ampliyfikator.
5. Dostosuj poziomy wyjściowe: The AX-ADCT2 features separate variable level adjustments for each channel. Use a small screwdriver to carefully adjust these potentiometers to match the input sensitivity of your aftermarket amplifier. Start with the levels at their minimum setting and gradually increase them until the desired output is achieved without distortion.
6. System testowy: Reconnect the vehicle's battery. Turn on the audio system and test for proper functionality. Adjust the level controls on the AX-ADCT2 and your amplifier as needed to achieve balanced sound.

5. Instrukcja obsługi

Once properly installed, the AX-ADCT2 operates automatically. When the vehicle's audio system is turned on, the converter will activate, providing a low-level RCA signal to your aftermarket amplifier. The remote turn-on output will also activate, turning on the connected amplifier. The variable output controls allow you to fine-tune the signal level to prevent distortion and achieve optimal sound quality from your ampliyfikator.

6. Konserwacja

The AX-ADCT2 is designed for reliable, maintenance-free operation. However, periodic checks can ensure continued performance:

• Sprawdź połączenia: Periodically check all wiring connections to ensure they remain secure and free from corrosion. Loose connections can lead to signal loss or intermittent operation.
• Czysta jednostka: If necessary, gently wipe the exterior of the converter with a dry, soft cloth to remove dust. Do not use liquid cleaners.
• Kontrola środowiskowa: Ensure the mounting location remains free from excessive heat, moisture, or physical damage.

7. Rozwiązywanie Problemów

If you encounter issues with your AX-ADCT2, refer to the following troubleshooting guide:

8. Specyfikacje

9. Gwarancja i wsparcie

For warranty information or technical support, please refer to the official Axxess or Metra Electronics website, or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.